manualshive.com logo in svg

Eelectron BO08A01KNX, Руководство по продукту

Поделиться
Скачать
Eelectron BO08A01KNX Скачать руководство пользователя страница 29

BO08A01KNXFI01010002.DOC 

 

 

 

Din Rail 8 Output Module– Product Handbook 

 

29/51 

Eelectron SpA, Via Magenta 77/22, I-20017 Rho (MI), Italia 
+39 02.9316681  +39 02.93507688  
[email protected]  www.eelectron.com 

BO08A01KNXFI01010002.DOC 

C.F. e P.IVA 11666760159 
Capitale sociale: 800.000,00€ interamente versato 
Tribunale di Milano 359157-8760-07 
CCIAA Milano 148549 

Position when Lock Ends 

  Relay is Deactivated  

  Relay is Activated  

  Keep previous state and ignore telegrams 

 Keep previous state and don’t ignore 

telegrams 

 

  Relay is Deactivated  

Relay is in “OFF” position (

See note 2

). 

  Relay is Activated  

Relay is in “ON” position (

See note 2

). 

  Keep previous state and ignore telegrams 

Relay returns in the state it was before 
lock function became active 

  Keep previous state and don’t ignore telegrams 

the output channel returns to its condition 
prior to the activation of the block unless 
you have received a telegram on the 
switch object or scenario; in this case, 
the last command received is executed. 

 
 
 

NOTES: 
 

[1]

: If the parameter “Initial Value for Lock Object” has the same value of “Telegram for Lock 

Activation” happens that, on power up, the output channel starts in lock mode, waiting for a 
“unlock” telegram in order to become active. Note that, even if the relay starts with lock function 
already active it does not go automatically in the position defined by the parameter “Relay 
Position when Lock is Active “; because this behaviuor is determined only by the parameter 
“Behaviour on power up” 

 

[2]

: The “activated” and “deactivated” conditions for each output channels correspond to ON or 

OFF condition upon the settings made for the “Contact Type” parameter.

 

 

6.12. Scene Function 

 

 

Содержание BO08A01KNX




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды