Eelectron BO08A01KNX Скачать руководство пользователя | Manualshive

Страница: 12 / 51

background image

BO08A01KNXFI01010002.DOC

Din Rail 8 Output Module– Product Handbook

12/51

Eelectron SpA, Via Magenta 77/22, I-20017 Rho (MI), Italia
+39 02.9316681 +39 02.93507688
[email protected] www.eelectron.com

BO08A01KNXFI01010002.DOC

C.F. e P.IVA 11666760159
Capitale sociale: 800.000,00€ interamente versato
Tribunale di Milano 359157-8760-07
CCIAA Milano 148549

KNX PARAMETER

SETTINGS

System Type



2 pipes system



4 pipes system

2 pipe system: the hydraulic system is unique and conveys the warm or cold fluid, depending on
the season.

4-pipe system: the hydraulic system has 2 individual circuits, one for heating and one for the
cooling.

Relay state when valve is deactivated



Relay is open when valve is deactivated



Relay is closed when valve is deactivated

Set if the relay must switch ON or OFF in order to Open / Close the valve; the deactivated state
for the valve is when it is closed and the fluid does not pass through.

5.3. Fan Coil Speed Control

The control of 3-speed fan coil can be achieved with 3 communication objects (1 bit) which accept
commands on / off or with a 1-byte communication object for a proportional control.

KNX PARAMETER

SETTINGS

Delay between Speed Changes (Sec.)

1… 255

This parameter set the pause time between the switching off the relay which control one speed
and the switching on of another relay to activate the next speed

Object type for speed control



3 x 1 bit objects



1 x 1 byte object

This set the data type for the speed control.

Object type for speed status



3 x 1 bit objects



1 x 1 byte object

This set the data type for the speed feedback to be sent on the bus.

Delay on ventilation start (min)

0 … 15

This parameter has effect only in heating mode and introduces a time delay between the
reception of a command which starts the fan speed and the real starting time in order to avoid to
blow cold air instead of warm due to the fact the hydraulic system need a certain time to supply
the hot fluid to the fan coil.

The delay, however, is introduced only when the fan coil actuator activates one of his speeds
starting from the state of no active speed (S1, S2, S3 are all off).

«
...
10
11
12
13
14
...
»

Содержание BO08A01KNX




















































Отзывы:

Нет отзывов

Похожие инструкции для BO08A01KNX

Бренд: zipwake Страницы: 12

Бренд: jbc Страницы: 12

SecurAccess PMR

Бренд: Depaepe Telecom Страницы: 51

Бренд: Omniflex Страницы: 2

Бренд: Controlsoft Страницы: 12

Бренд: Medion Страницы: 308

Бренд: Commax Страницы: 10

Бренд: Qingdao Desiree Страницы: 22

Бренд: Ravaglioli Страницы: 82

Бренд: YA Страницы: 2

Бренд: M-system Страницы: 4

Бренд: iTrak Страницы: 6

Бренд: M-E Страницы: 72

Бренд: AMGO Hydraulics Страницы: 40

Бренд: Elo Touch Solutions Страницы: 3

NANOpure DIamond D11931

Бренд: Barnstead|Thermolyne Страницы: 56

Бренд: BAS-IP Страницы: 8

Бренд: CyberData Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды