Eaton Moeller SmartWire-Darwin EU5C-SWD-CAN Скачать руководство пользователя

Страница: 89 / 108

Object list

02/09 AWB2723-1612en

Dynamic entries

The following new entries in the object list are generated
each time the gateway is started:

Module list 0x1027

Area 0x2100 to 0x22FF: properties of the SmartWire Darwin
modules

Area 0x6000 to 0x6FFF: utility data of the SmartWire Darwin
modules.

Specification of the dynamic object list entries is performed
depending on the target configuration.

Input and output data of the individual SWD slaves are
mapped into the PDOs in the order of the SWD network
structure.

“Input byte” entry

All input bytes of the SWD slaves are listed.

“Input word” entry

All word input data of the SWD slaves are lined up.

“Output byte” entry

All output bytes of the SWD slaves are lined up.

“Output word” entry

All word output data of the SWD slaves are lined up.

Module list (0x1027)

Content

Subindex = 0 (U8): the subindex 0 specifies the number of
SmartWire Darwin slaves registered in the target
configuration.

Subindex = 1 (U16): module no: an entry (module ID) is
generated with the order in which the SmartWire-Darwin
slaves were recorded in the target configuration. This entry
is formed from the stringing together of the vendor ID and
device ID.

Содержание Moeller SmartWire-Darwin EU5C-SWD-CAN













































































































Результаты поиска

Содержание Moeller SmartWire-Darwin EU5C-SWD-CAN

Отзывы:

Похожие инструкции для Moeller SmartWire-Darwin EU5C-SWD-CAN

Бренды по названию

Популярные бренды

Eaton Moeller SmartWire-Darwin EU5C-SWD-CAN, Аппаратное обеспечение и инженерия

Результаты поиска

Содержание Moeller SmartWire-Darwin EU5C-SWD-CAN

Отзывы:

Похожие инструкции для Moeller SmartWire-Darwin EU5C-SWD-CAN

Бренды по названию

Популярные бренды