Eaton Moeller SmartWire-Darwin EU5C-SWD-CAN Скачать руководство пользователя | Manualshive

Страница: 58 / 108

background image

Commissioning

54

02/09 AWB2723-1612en

Switching on for initial startup, a replacement or a
changed SmartWire Darwin configuration

Prerequisite for reading the configuration:

• All SmartWire Darwin slaves are connected to the

SmartWire Darwin line.

• The SmartWire-Darwin network is connected to the

gateway.

• Voltage POW is applied to the gateway and the power LED

lights up.

• The voltage AUX is applied (if necessary).
• The SmartWire-Darwin status LEDs of the SmartWire-

Darwin slaves are on or are flashing.

X

Press the configuration button on the gateway for at least
two seconds. The SmartWire status LED on the gateway
begins to flash orange. The SmartWire-Darwin status LEDs
on the SmartWire-Darwin slaves also flash. All slaves are
addressed in sequence, the complete configuration is
stored retentively (gateway target configuration). The
gateway is then restarted (see next section).

j

Warning!

If a SmartWire-Darwin slave has failed, the SmartWire-
Darwin network can still be operated with the remaining
slaves, depending on the configuration setting (even after
a repeat power up of the gateway). The failure is reported
to the application. If there is a faulty configuration and the
configuration button is pressed, only the slaves up to the
failed device are addressed and stored. Use of the
remaining slaves is not possible until the defective slave
has been replaced and the configuration has been read in
again by pressing the configuration button.

«
...
56
57
58
59
60
...
»

Содержание Moeller SmartWire-Darwin EU5C-SWD-CAN













































































































Отзывы:

Нет отзывов

Похожие инструкции для Moeller SmartWire-Darwin EU5C-SWD-CAN

Бренд: unicore Страницы: 25

Бренд: unicore Страницы: 24

Бренд: IBM Страницы: 12

Бренд: K&K Страницы: 10

Бренд: B&R Industries Страницы: 89

vlt soft starter mcd 500

Бренд: Danfoss Страницы: 95

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 33

Бренд: Danfoss Страницы: 59

Бренд: Danfoss Страницы: 16

VLT AQUA Drive FC 200

Бренд: Danfoss Страницы: 91

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 100

Бренд: Danfoss Страницы: 82

Бренд: Danfoss Страницы: 18

Бренд: Danfoss Страницы: 12

OPTYMA Plus OP-LPQM

Бренд: Danfoss Страницы: 8

Бренд: GARAN Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды