Eaton Moeller SmartWire-Darwin EU5C-SWD-CAN Скачать руководство пользователя страница 97

Страница: 97 / 108

02/09 AWB2723-1612en

Monitoring error (node guarding/
heartbeat.)

Red asynchronous
flashing

SDO only

Communication error on the CAN bus. (Bus
Off.)

Red

Pre-operational initialization mode -
communication only possible via SDOs.

Green flashing

SDO only

Stopped - no data exchange.

Green asynchronous
flashing

Operational - data exchange is possible via
PDOs and SDOs.

Green

yes

Description

CAN status LED

Data exchange gateway
via CANopen to PLC

Description

SmartWire
Darwin-
configurations
LED

Data exchange gateway
via field bus to PLC

The planned configuration complies with
the gateway target configuration.

Green continuous
light

yes

The planned configuration does not comply
with the gateway target configuration, but
is compatible with it (list of the devices that
are compatible with one another

table 12, page 96.).

Flashing (green)

yes

The planned configuration and the
gateway target configuration are not
compatible.

Red continuous light

Содержание Moeller SmartWire-Darwin EU5C-SWD-CAN













































































































Результаты поиска

Содержание Moeller SmartWire-Darwin EU5C-SWD-CAN

Отзывы:

Бренды по названию

Популярные бренды

Eaton Moeller SmartWire-Darwin EU5C-SWD-CAN, Аппаратное обеспечение и инженерия

Результаты поиска

Содержание Moeller SmartWire-Darwin EU5C-SWD-CAN

Отзывы:

Бренды по названию

Популярные бренды