manualshive.com logo in svg

Eaton Moeller SmartWire-Darwin EU5C-SWD-CAN, Аппаратное обеспечение и инженерия

Поделиться
Скачать
Eaton Moeller SmartWire-Darwin EU5C-SWD-CAN Скачать руководство пользователя страница 60

Commissioning

56

02/09 AWB2723-1612en

selected the box 

Create SDO’s for Module List 

in the 

controller configuration). If the planned configuration 
complies with the stored gateway configuration, all status 
LEDs indicate a green continuous light.

Any errors that occur are indicated via the CANopen status 
LED and the Config status LED.

Table 5: CAN-Status-LED

So the prerequisite for a data interchange is that the 
configuration drawn up on the PLC system (= planned 
configuration) complies with the configuration actually 
available on the gateway. The result of this check is signalled 
on the gateway via the SmartWire-Darwin configuration 
LED.

Description

CAN-Status-LED

Data exchange gateway via 
the CANopen to PLC

CAN interface inactive.

off

no

Baud rate detection active on the CAN 
bus

Red strobe light

no

CAN baud rate detected ,waiting for a 
valid target configuration

orange

no

Communication error on the CAN bus 
(error warning level reached.)

Red flashing

yes

Monitoring error (node guarding/
heartbeat.)

flickering red flashing 
light

only SDO 

Communication error on the CAN bus 
(bus Off.)

red

no

Pre-operational initialization mode - 
communication only possible via SDOs

Green flashing

only SDO

Stopped - no data exchange

Green strobe light

no

Operational - data exchange is possible 
via PDOs and SDOs

Green

yes

Содержание Moeller SmartWire-Darwin EU5C-SWD-CAN













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды