Eaton Moeller SmartWire-Darwin EU5C-SWD-CAN Скачать руководство пользователя страница 88

Страница: 88 / 108

Programming

02/09 AWB2723-1612en

• 1 = the SWD gateway also starts up without comparison

between the planned configuration and the target
configuration. This setting is conceived for CANopen
configurators that do not support downloading of the
planned module list to the gateway.

If a planned configuration is downloaded to the gateway, a
comparison of the configurations takes place.

• 0 = the comparison between planned configuration and

target configuration is mandatory (default setting).

Read access

Delivers back the currently valid setting.

Write access

Definition of the desired behaviour.

DiagFlags (0x2004)

Content

Via this entry the current status of the diagnostic flags in
accordance with table table 9 page 76 can be read out.

Read access

The current status of the diagnostic flags is returned.

Write access

Not permissible.

Delay between cyclic exchange (0x2010)

Content

Pause time between two SWD cycles in milliseconds
(0 - 255 ms)

Read access

Currently set pause time

Write access

Pause time to be set

At present this parameter cannot be changed.

Содержание Moeller SmartWire-Darwin EU5C-SWD-CAN













































































































Результаты поиска

Содержание Moeller SmartWire-Darwin EU5C-SWD-CAN

Отзывы:

Бренды по названию

Популярные бренды

Eaton Moeller SmartWire-Darwin EU5C-SWD-CAN, Аппаратное обеспечение и инженерия

Результаты поиска

Содержание Moeller SmartWire-Darwin EU5C-SWD-CAN

Отзывы:

Бренды по названию

Популярные бренды