Eaton APS12-300 Series Скачать руководство пользователя страница 62

Страница: 62 / 120

Access Power Solutions Installation and Operation Guide (APS6-300/500 and APS12-300 Series)

IPN 997-00012-49G May 2013

Problem

Possible Cause

Required Action

Incorrect battery or load
current readings.

Bus voltage sense polarity is
incorrect.

Check the bus voltage sense polarity and
correct if necessary.

Incorrectly configured shunt
inputs.

Check shunt mapping and gain is correct.

Current is within the

Battery

State Threshold

. See details in the

System Controller Operation
Handbook.

None, normal operation.

SC200 or SC100 or
DCTools/Web displays

???

N/A

Failed, disconnected or
unconfigured sensor.

Replace, connect or configure sensor.

Faulty or disconnected voltage
feed module.

Replace or connect voltage feed module.

Incorrect I/O board mapping
(SC200 only).

Check I/O board mapping. See details in
the System Controller Operation
Handbook.

SC200 or SC100 displays

Config Error

Missing or invalid configuration
file.

Either:
Load a valid configuration file into the
SC200 or SC100. See Backup and Restore
on page

, or

Change one or more configuration
settings using the SC200 or SC100 keypad
or DCTools.

Incorrect rectifier voltage,
because installed rectifiers have
different output voltages.

Check that all rectifiers are of the same
type and replace as necessary.

DCTools connection
problem (

Target Failed to

Respond

error)

Connection problem

Refer to following communications
problems.

USB communications
problem (SC200 only)

Incorrect, disconnected or faulty
cable.

Check a USB A/B cable is plugged into
the USB port and a PC USB port.
Replace faulty cable.

SC200 or SC100 serial
communications are disabled.

Check

S3P Access

is enabled. See details

in the System Controller Operation
Handbook.

DCTools not installed on PC or
wrong version.

Install latest version of DCTools.
Download from
dcpower.eaton.com/downloads.

Password required to change
settings.

See Write Access Password in the System
Controller Operation Handbook.

Содержание APS12-300 Series


















































































































Результаты поиска

Содержание APS12-300 Series

Отзывы:

Похожие инструкции для APS12-300 Series

Бренды по названию

Популярные бренды

Eaton APS12-300 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание APS12-300 Series

Отзывы:

Похожие инструкции для APS12-300 Series

Бренды по названию

Популярные бренды