Duplo DF-990 Скачать руководство пользователя

Страница: 39 / 100

Chapter 2 Basic Operation

46 mm/1.81 inches

Stack paper on the paper feed tray.

Push in the paper until the lead edge touches

the paper feed inlet lightly.

Maximum paper stacking height: 46 mm/1.81

inches.

Adjust the paper feed guide to match

the paper size.

Set the paper feed guide in such a way that it

touches the paper lightly.

•

Do not press the paper with the paper feed guides too strongly. Otherwise, paper feed errors

such as mis-feed will occur.

•

If the guides are positioned incorrectly, the automatic paper size detection function will not

work, and the test key and start key,etc. will not operate. (DF-999/DF-999A)

Tighten the guide fixing screws.

Make sure to tighten the guide fixing

screws on both right and left sides. If the

screws are not fixed, the paper feed guide

moves during operation, and folding

misalignment may occur in the right and

left direction.

Lower the paper set lever.

The paper feed stand will go up to the paper feeding position when the paper set lever is lowered.

When the paper feed tray is not set at the feed position, even if you press the

key or

key,

[Position Err Paper Feed Tray] will be displayed and operation will not start. (DF-990/DF-990A)

Automatic rise/descent of the paper feed tray (DF-999/DF-999A)

When paper is stacked on the paper feed tray, the paper feed guides are set, and the

key is pressed,

the paper feed tray rises automatically.

When using large or heavy paper, the paper feed tray may become over stacked and may not be

able to rise due to paper weight. In such cases, stack less paper.

• The paper feed tray descends automatically when paper is removed from the paper feed tray. It will also

descends automatically when paper runs out on the paper feed tray during a folding operation.

• When [Detection] is turned off, the paper stacked on the tray is not detected. Therefore, when the

operation stops, the paper feed tray goes down automatically even if paper is stacked on the tray.

Chapter 3 “8-5. Detection” (p.65)

Содержание DF-990





































































































Результаты поиска

Содержание DF-990

Отзывы:

Похожие инструкции для DF-990

Бренды по названию

Популярные бренды

Duplo DF-990, Инструкция по эксплуатации

Результаты поиска

Содержание DF-990

Отзывы:

Похожие инструкции для DF-990

Бренды по названию

Популярные бренды