Duplo DF-990 Скачать руководство пользователя

Страница: 46 / 100

Chapter 3 Advanced Operation

Chapter 3 Advanced Operation

1. Correcting Folding Misalignment

Folding misalignment consists of “folding misalignment along the sides of the paper” and “folding

misalignment along the vertical length of the paper”. Other than this, “deformed folding” may also occur due

to paper characteristics, etc.

Depending on the usage environment (temperature and humidity), paper type, thickness, paper grain

direction, trimming accuracy, and printing states folding misalignment may occur.

Do not put fingers inside during operation.

Keep away long hair, ties, jewelry and loose clothing.

It could cause injury.

1-1. Adjustment folding misalignment in right and left direction

Ejection

direction

When the folded paper is misaligned along

the sides, correct using the skew correction

knob of the paper feed tray.

Check that the paper feed guides are

set correctly.

Gaps between the paper and paper feed

guides will cause folding misalignment along

the sides to occur easily.

Proceed to step 2 if the paper feed guides are

set properly.
Perform test folding after resetting the paper

feed guides. Proceed to step 2 if folding

misalignment occurs after setting the paper

feed guides properly.

Remove the paper stacked on the paper feed tray.

Adjustments cannot be made effectively by adjusting folding misalignment with skew correction knob

when the leading edge of paper is in contact with the guide plate.

Содержание DF-990





































































































Результаты поиска

Содержание DF-990

Отзывы:

Похожие инструкции для DF-990

Бренды по названию

Популярные бренды

Duplo DF-990, Инструкция по эксплуатации

Результаты поиска

Содержание DF-990

Отзывы:

Похожие инструкции для DF-990

Бренды по названию

Популярные бренды