DriSteem XT Series Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 68

background image

50

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Note:

DriSteem recommends keeping a spare steam
cylinder in stock during the humidiﬁ cation
season. See “Replacement parts" on Pages
57 and 59.

1. When steam cylinder is completely empty, turn humidifier off. Place all

power disconnects in OFF position, and lock in OFF position.

2. Remove cabinet doors, and make sure cylinder and humidifier components

have cooled.

3. Carefully pull the electrode plugs straight up off the cylinder to ensure no

damage to the plug boot occurs.

4. Inspect cylinder plugs. Obtain replacement plugs from DriSteem if

deterioration, corrosion or loose fit occur.

5. Disconnect the high water sensor wire.

Note:

Because of tight clearances, perform Steps 6 through 7 only if
servicing Model XTP 002 through 017 with top-mounted steam
blower. For all other models, skip to Step 8.

6. Remove both clamps on steam hose that connects to cylinder and

steam blower.

7. Slide steam hose from Step 6 all the way up until it is tight

against bottom of steam blower. Skip to Step 9.

8. Loosen steam hose clamp, and disconnect steam hose from cylinder.

9. Place hands palms-down below cylinder on both sides of drain outlet.

10. Press up against bottom of cylinder with backs of hands while pressing

down against cabinet floor with fingers.

11. Raise cylinder until drain outlet clears drain valve body and the side tabs

on the cylinder have cleared the cylinder guides. Remove cylinder from
cabinet.

12. Vacuum scale and debris out of drain valve port.

Note:

For more thorough cleaning, see drain valve maintenance instructions
on Page 51.

13. Replace O-ring in drain valve body (new cylinder ships with new O-ring).

Make sure O-ring is correctly placed.

14. Dampen O-ring seals

with water

before replacing cylinder.

Do not use

lubricant or other substance.

15. Install new steam cylinder. See “Installing steam cylinder” on Page 12.

16. Connect steam hose to cylinder, and re-install hose clamp.

17. Connect high water sensor (yellow) wire to single pin surrounded by

plastic shoulder on cylinder.

18. Connect electrode wires to pins on top of cylinder. Make sure all plugs fit

snugly and are fully engaged on pins.

Important:

Three phase cylinders have color-coded dots on the cylinder

and color bands on the electrode plugs. When connecting the plugs, match
the band colors on the plugs with the dot colors on the cylinder. Refer to the
wiring diagram shipped with the humidiﬁ er if necessary.

If returning humidiﬁ er to operation, see the start-up procedure on page 48.

Maintenance:

MAINTENANCE

Replacing steam cylinder

CAUTION

If cylinder plugs become loose,

damage to the humidiﬁ er may occur.
Obtain replacement plugs from
DriSteem. See “Replacement parts”
on Pages 57 and 59 for part
numbers.

«
...
52
53
54
55
56
...
»

Содержание XT Series





































































Отзывы:

Нет отзывов

Похожие инструкции для XT Series

23-11-2242N-005

Бренд: Maytag Страницы: 16

Бренд: Oasis Страницы: 2

CDAS HL 050 Series

Бренд: Parker Страницы: 398

Бренд: Bionaire Страницы: 8

Бренд: Bionaire Страницы: 8

PLATINUM GPDH390

Бренд: Goldair Страницы: 12

Бренд: SteamOvap Страницы: 44

Бренд: Munters Страницы: 20

Бренд: TriStar Страницы: 48

Бренд: Oasis Страницы: 16

Бренд: TurMix Страницы: 15

EHUMD800ASM00BA

Бренд: Trane Страницы: 48

Бренд: Yoer Страницы: 24

Бренд: Klarstein Страницы: 24

Бренд: Uberhaus Страницы: 23

ElectroVap MC2 Series

Бренд: Devatec Страницы: 14

Comfort-Aire BHD-501-D

Бренд: Heat Controller Страницы: 6

Бренд: Black & Decker Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды