DriSteem XT Series Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 68

background image

10

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

INSTALLATION

Unpack the humidiﬁ er from the shipping carton, and remove the cabinet doors
and steam cylinder (see removing steam cylinder instructions below).

Note: When ﬁ rst unpacking the humidiﬁ er, cut and remove the shipping strap

that goes around the cylinder and through the cylinder guides. This strap
does not need to be replaced.

REMOVING STEAM CYLINDER

If sent to this page from the “Maintenance” section, and the humidiﬁ er has
been operating, make sure the cylinder is empty and cooled before removing
it. See the shutdown and cool-down procedures on Page 49.

1. Carefully pull the electrode plugs straight up off the cylinder to ensure no

damage to the plug boot occurs.

2. Disconnect the high water sensor wire.

3. Place hands palms-down below cylinder on both sides of drain outlet.

4. Press up against bottom of cylinder with backs of hands while pressing

down against cabinet floor with fingers.

5. Raise cylinder until drain outlet clears drain valve body and the side tabs

on the cylinder have cleared the cylinder guides. Remove cylinder from
cabinet.

WALL MOUNTING HUMIDIFIER

Mount the humidiﬁ er level and plumb using the lag bolts provided. Follow the
instructions below for mounting on a wood stud wall.

1. Mount spanner boards on wall, spanning at least two studs. Position one

board at top of cabinet (for the lag bolts), and other board at bottom of
cabinet.

2. Predrill pilot holes in spanner boards, and secure humidifier to spanner

boards with lag bolts.

Note: Use the appropriate mounting methods and mounting hardware for other

wall types.

Mounting

WARNING

Mounting hazard

Mount humidiﬁ er per the instructions
in this manual and to a structurally
stable surface. Improper mounting of
the humidiﬁ er can cause it to fall or tip,
resulting in severe personal injury or
death.

«
...
12
13
14
15
16
...
»

Содержание XT Series





































































Отзывы:

Нет отзывов

Похожие инструкции для XT Series

Master DH 721 P

Бренд: Dantherm Страницы: 77

Бренд: Rohnson Страницы: 14

Polaris EX CPAP with SoftX ISP3000

Бренд: Invacare Страницы: 44

Бренд: TaoTronics Страницы: 13

homeSteam UM 001

Бренд: Carel Страницы: 30

Бренд: Enviracaire Страницы: 36

Бренд: GEAppliances Страницы: 20

Gaby's world Pommy

Бренд: Lanaform Страницы: 68

Бренд: OSKAR Страницы: 20

Бренд: Crane Страницы: 12

Бренд: Venta Страницы: 26

Бренд: Vapac Страницы: 10

Бренд: Trotec Страницы: 17

Бренд: N'oveen Страницы: 39

Бренд: Danby Страницы: 24

Бренд: Danby Страницы: 28

Бренд: Munters Страницы: 36

Бренд: Wood’s Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды