DriSteem XT Series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 68

background image

14

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

INSTALLATION

Field piping overview

OM-7973

Install
plumb

3/4" (DN20) drain piping up to
second drain connection

Supply valve, by installer

Drain hose and clamp*

Inlet strainer, by installer

Notes:
• Dashed lines indicate provided by installer.
• Two-cylinder model shown.
* Ships with humidiﬁ er

Shock arrester
(by installer)
recommended
to reduce water
hammer

Floor
drain

Open drains required directly
below humidiﬁ er drains to prevent
downstream drain line blockage
from causing water to back up into
cylinder. Refer to governing codes
for drain pipe size and maximum
discharge water temperature. Install
spill funnels plumb to ﬂ oor drain.

Metallic water
supply line

3/8" (DN10) copper water supply line; water
pressure must be 25 to 80 psi (175 to 550 kPa).

Fill valve with 1/4" FIP
(3/8" BSP [DN10] in
Europe) supply water
connection

1¼" (DN32) drain piping after
second drain connection, or if
piping run is over 10’ (3 m).

1" (25 mm) air gap required to
isolate unit drain piping from sanitary
drain piping. Locate air gap only in
spaces with adequate temperature
and air movement to absorb ﬂ ash
steam, or condensing on nearby
surfaces could occur.

Steam hose or tubing. DriSteem
recommends tubing for runs longer than
10' (3 m). See Table 26-1 for maximum
tubing lengths. Tubing must be grounded.

Pitch 1/8"/ft (1%) toward drain

Piping:

FIGURE 14-1: XT SERIES HUMIDIFIER FIELD PIPING OVERVIEW

«
...
16
17
18
19
20
...
»

Содержание XT Series





































































Отзывы:

Нет отзывов

Похожие инструкции для XT Series

Бренд: Aerial Страницы: 30

cont21200810247

Бренд: Conti+ Страницы: 12

Gallery FGAC7044U1

Бренд: Frigidaire Страницы: 11

Бренд: Frigidaire Страницы: 13

Бренд: Frigidaire Страницы: 12

Бренд: Frigidaire Страницы: 11

Gallery FGAC5044W10

Бренд: Frigidaire Страницы: 13

Бренд: Frigidaire Страницы: 15

Бренд: Frigidaire Страницы: 13

FRIGIDAIRE DEHUMIDIFIER 2020264A0429

Бренд: Frigidaire Страницы: 8

Бренд: MSW Motor Technics Страницы: 11

Бренд: Livart Страницы: 7

Бренд: RS PRO Страницы: 36

DRY 300 PLASTIK

Бренд: MICROWELL Страницы: 33

Бренд: Goldstar Страницы: 32

Бренд: Goldstar Страницы: 32

Бренд: Goldstar Страницы: 34

Бренд: Emerson Quiet Kool Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды