DriSteem XT Series Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 68

background image

36

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Rapid-sorb and Ultra-sorb with Models XTP 050 through 096

Models XTP 050 through XTP 096 have capacities requiring dispersion devices with condensate drains (Figure 35-1).
For these models, DriSteem recommends the following:

• Run separate steam tubing from each cylinder to the connection on the dispersion device.

• Pitch steam tubing toward the dispersion device.

The installer should not attempt to drain condensate back to the cylinder. When a vertical riser is required in the steam
tubing, a drip tee is required in order to eliminate a condensate collection point that will restrict steam ﬂ ow.

OM-7982-XT

Pitch*

Pitch*

Drain

Drain

Drip tee

Pitch*

Pitch*

Drain

Rapid-sorb steam dispersion panel

Ultra-sorb steam dispersion panel

Dual-cylinder XT Series humidiﬁ er

WARNING

Preventing back pressure in dual-cylinder humidifi ers

Read and follow all steam tubing installation instructions
for dual-cylinder humidiﬁ ers. Failure to follow these
instructions could result in excessive back pressure and
the risk of equipment damage or severe personal injury.

Notes:
* Pitch 1/8"/ft (1%) minimum toward dispersion panel.
• See installation notes in Figure 25-1.

FIGURE 36-1: DUAL-CYLINDER XT SERIES HUMIDIFIER CONNECTED TO RAPID-SORB OR ULTRA-SORB WITH RISER DRIPS IN
STEAM SUPPLY LINES

INSTALLATION

Dispersion:

«
...
38
39
40
41
42
...
»

Содержание XT Series





































































Отзывы:

Нет отзывов

Похожие инструкции для XT Series

Бренд: NANO Страницы: 26

Бренд: Waves Страницы: 25

Бренд: ETI Страницы: 4

Бренд: Dantherm Страницы: 32

COMBINED DEHUMIDIFIER

Бренд: DeLonghi Страницы: 12

Бренд: happyhaves Страницы: 14

Бренд: GE Страницы: 24

Бренд: AMW Страницы: 31

Бренд: Whirlpool Страницы: 4

Бренд: Whirlpool Страницы: 1

Бренд: Whirlpool Страницы: 12

Бренд: Whirlpool Страницы: 12

Бренд: Whirlpool Страницы: 14

Бренд: Whirlpool Страницы: 12

Бренд: Whirlpool Страницы: 16

Бренд: Whirlpool Страницы: 12

Бренд: Whirlpool Страницы: 12

Бренд: Whirlpool Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды