DriSteem XT Series Скачать руководство пользователя страница 58

Страница: 58 / 68

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Troubleshooting

Table 53-1:
Model XTP humidifier troubleshooting guide (continued)

Problem

Possible cause

Action

Water in duct from dispersion
tube.

Dispersion tube installed
incorrectly

Install dispersion tube with tubelets facing straight up.

Impurities in steam hose or
tubing causing foaming

Rinse cylinder and hose in clean water.

Service

light ﬂ ashing red before

end of humidiﬁ cation season.

Cylinder full of mineral deposits

Plumb humidiﬁ er to ﬁ ltered water.

Plumb humidiﬁ er to softened water.

Steam

light is yellow.

Humidiﬁ er operating below
rated capacity

Notes:

• This is normal for systems

plumbed to low-conductivity
water and systems that
operate for short cycles.

• XT Series humidiﬁ er

recommended ﬁ ll water
conductivity is
125 to 1250 μS/cm.

Plumb humidiﬁ er to softened water.

To determine operating current, attach clamp-on ammeter to one of the electrode
wires on top of cylinder.

Add add 1/4 to 1/2 tab sodium bicarbonate (i.e., Alka Seltzer) to water in cylinder
increase water conductivity. Consult DriSteem for further advice.

Humidiﬁ er is not satisfying
demand.

Control setting too low

Adjust control to higher setting.

Control mounted in wrong
location

See installation instructions with control for correct mounting location.

Excess humidity.

Control setting too high

Adjust control to lower setting.

Control mounted in wrong
location

See installation instructions with control for correct mounting location.

MAINTENANCE

Содержание XT Series





































































Результаты поиска

Содержание XT Series

Отзывы:

Похожие инструкции для XT Series

Бренды по названию

Популярные бренды

DriSteem XT Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание XT Series

Отзывы:

Похожие инструкции для XT Series

Бренды по названию

Популярные бренды