DriSteem XT Series Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 68

background image

44

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

WIRING XT STEAM BLOWERS

Make the following wiring connections between the humidiﬁ er and the XT
steam blower, and tighten all terminals securely:

Fuses provided. See page "XT steam blowers" on page 40.

Connect XT steam blower fan wires to humidiﬁ er terminals 32, 33, and GRD.

Refer to the external connections diagram shipped with the XT steam blower.

PIPING CONDENSATE TO HUMIDIFIER FILL CUP

1. Remove fill cup cap from XT Series humidifier, and drill a 1/2" (13 mm)

hole in fill cup cap for SDU-006E and SDU-017E condensate hose as
shown in Figure 44-1.

2. Route XT steam blower condensate hose through hole in fill cup cap, and

secure condensate hose in place.
Note: Make sure condensate hose has a water seal, as shown in Figure

44-2. The water seal is required to ensure condensate drainage
from the XT steam blower and to keep steam from blowing out of the
condensate hose.

PIPING CONDENSATE TO DRAIN

The XT steam blower condensate hose must be routed as shown in Figure
44-2. The water seal is required to ensure condensate drainage from the XT
steam blower and to keep steam from blowing out of the condensate hose.

After the water seal, run the condensate hose to an open drain. Cut the hose
at a 45 degree angle on the end above the drain to permit a direct stream of
water into the drain while maintaining an air gap.

The condensate hose must be installed and sized according to governing
codes.

ADDITIONAL INSTRUCTIONS

See instructions for piping from XT Series humidiﬁ er to XT steam blower on
pages 15 and 16.

Condensate
hose

Plastic tie

Spill funnel
(plumb to ﬂ oor
drain)

Open ﬂ oor
drain. Refer
to governing
codes for drain
pipe size and
maximum
temperature
requirements.

1” (25 mm)
air gap

OM-7687

7” (178 mm)
water seal

Note:
Shown with condensate to open drain.
Condensate can also be returned to ﬁ ll cup
through ﬁ eld-installed hole in ﬁ ll cup cap. See
Figure 44-1.

SDU-017E shown

OM-7636X

Approximate cap
orientation to front of
XT Series humidiﬁ er cabinet

Field-installed hole in
ﬁ ll cup cap for remote
XT steam blower

Drill hole here for XT steam blower
condensate hose

FIGURE 44-1: PIPING CONDENSATE TO
HUMIDIFIER FILL CUP

INSTALLATION

XT steam blowers

Dispersion:

FIGURE 44-2: PIPING CONDENSATE TO
DRAIN

«
...
46
47
48
49
50
...
»

Содержание XT Series





































































Отзывы:

Нет отзывов

Похожие инструкции для XT Series

ComfortBREEZE CB100

Бренд: Trion Страницы: 16

Бренд: Steba Страницы: 48

Бренд: COMFORT-AIRE Страницы: 24

Бренд: happyhaves Страницы: 14

Бренд: MS Electronics Страницы: 4

Бренд: Silvercrest Страницы: 36

Бренд: Silvercrest Страницы: 54

Бренд: Silvercrest Страницы: 80

Бренд: Silvercrest Страницы: 88

Бренд: Silvercrest Страницы: 100

Бренд: Levoit Страницы: 12

Бренд: Ivation Страницы: 6

Бренд: GeneralAire Страницы: 12

compactSteam XL

Бренд: Carel Страницы: 54

Бренд: Carel Страницы: 48

Бренд: Bionaire Страницы: 8

Бренд: Bionaire Страницы: 8

Бренд: Nordic Home Culture Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды