DriSteem XT Series Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 68

background image

ii

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

WARNING

Attention installer

Read this manual before installing, and leave this manual with product owner. This product must be installed by qualiﬁ ed
HVAC and electrical contractors. Installation must be code approved. Improper installation can cause property damage,
severe personal injury, or death as a result of electric shock, burns, or ﬁ re.

DriSteem

®

Technical Support: North America: 800-328-4447

Europe:

+3211823595

Read all warnings and instructions

Read this manual before performing service or maintenance procedures on any part of the system. Failure to follow all
warnings and instructions could produce the hazardous situations described, resulting in property damage, personal injury,
or death.

Failure to follow the instructions in this manual can cause moisture to accumulate, which can cause bacteria and mold
growth or dripping water into building spaces. Dripping water can cause property damage; bacteria and mold growth can
cause illness.

Hot surfaces and hot water

This steam humidiﬁ cation system has extremely hot surfaces. Water in steam cylinders, steam tubing, and dispersion
assemblies can be as hot as 212 °F (100 °C). Discharged steam is not visible. Contact with hot surfaces, discharged hot
water, or air into which steam has been discharged can cause severe personal injury. To avoid severe burns, follow the
cool-down procedure in this manual before performing service or maintenance procedures on any part of the system.

Disconnect electrical power

Disconnect electrical power before installing supply wiring or performing service or maintenance procedures on any part of
the humidiﬁ cation system. Failure to disconnect electrical power could result in ﬁ re, electrical shock, and other hazardous
conditions. These hazardous conditions could cause property damage, personal injury, or death.

Contact with energized circuits can cause property damage, severe personal injury, or death as a result of electrical shock
or ﬁ re. Do not remove cabinet doors until electrical power is disconnected.

Follow the shutdown procedure on Page 49 before performing service or maintenance procedures on any part of the
system.

Warnings and cautions

WARNING

CAUTION

Indicates a hazardous situation that could result in death or
serious injury if instructions are not followed.

Indicates a hazardous situation that could result in damage to or
destruction of property if instructions are not followed.

WARNINGS AND CAUTIONS

«
1
2
3
4
...
»

Содержание XT Series





































































Отзывы:

Нет отзывов

Похожие инструкции для XT Series

Бренд: East Страницы: 12

Бренд: Danby Страницы: 39

Бренд: Baseus Страницы: 30

Бренд: Classic Страницы: 6

Бренд: EBCO Страницы: 4

Бренд: Shini Страницы: 83

Бренд: Crane Страницы: 12

Бренд: HIdRos Страницы: 52

MJ-E14CG-S1-SWE

Бренд: Mitsubishi Electric Страницы: 28

Бренд: Mitsubishi Electric Страницы: 39

Бренд: Mitsubishi Electric Страницы: 28

Бренд: Mitsubishi Electric Страницы: 49

Бренд: Mitsubishi Electric Страницы: 39

Бренд: Mitsubishi Electric Страницы: 56

Бренд: Mitsubishi Electric Страницы: 28

Бренд: Mitsubishi Electric Страницы: 28

Бренд: Mitsubishi Electric Страницы: 24

Бренд: Mitsubishi Electric Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды