DriSteem XT Series Скачать руководство пользователя страница 52

Страница: 52 / 68

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Model XTP

START-UP PROCEDURE

After the Model XTP humidiﬁ er is installed and connected properly:

1. Perform all applicable “Start-up checklist” items on Page 47.

2. Read and follow the instructions in the “Operation” section of the

Vapor-logic Installation and Operation Manual

3. Note: During start-up, do not leave the humidifier unattended.

4. Monitor humidifier operation through multiple drain and fill cycles.

5. Perform the cleaning procedure as follows:

a. Operate humidiﬁ er long enough for steam to be produced.

b. Using the keypad/display:

– At the Main menu, select Tank Status, and press Enter.
– Select Mode, and press Enter.
– Select Drain, and press Enter.
– Let steam cylinder drain for 5 to 10 minutes until empty.

c. Restart the humidiﬁ er, and repeat Steps a and b.

CAPACITY LIMITATION

Model XTP humidiﬁ er capacity can be limited to a user-speciﬁ ed maximum
using the keypad/display or Web interface. From the Main menu, select

Tank

Setup

, then select

Capacity Adjustment

for menu options.

WARNING

Electric shock hazard

Only qualiﬁ ed electrical personnel
should perform start-up procedure.

Contact with energized circuits can
cause property damage, severe
personal injury or death as a result of
electrical shock or ﬁ re.

Make sure cabinet doors are installed
before turning on electrical power.

For proper operation of safety interlock
switch, install electrical-side door ﬁ rst,
then install cylinder-side door.

The

Vapor-logic In stal la tion and Op er a tion

Man u al

is a comprehensive operation manual.

Refer to it for information regarding the
following features:

• Keypad/display and Web interface setup

and menu information

• Control input signals and functions
• Safety features
• Alarm screens and fault messages

This manual ships with Model XTP
humidiﬁ ers and is available at our website:
www.dristeem.com

OPERATION

Содержание XT Series





































































Результаты поиска

Содержание XT Series

Отзывы:

Похожие инструкции для XT Series

Бренды по названию

Популярные бренды

DriSteem XT Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание XT Series

Отзывы:

Похожие инструкции для XT Series

Бренды по названию

Популярные бренды