DriSteem XT Series Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 68

background image

22

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

INSTALLATION

XT Series humidifier steam outlet

The steam outlet on the humidiﬁ er is sized
to the output of the humidiﬁ er. DO NOT use
interconnecting steam hose or tubing with an
inside diameter smaller than the humidiﬁ er
steam outlet. Reducing the inside diameter will
result in the internal humidiﬁ er system pressure
exceeding the parameters for acceptable
performance.
• See maximum steam carrying capacities in

Table 26-1 and 27-1.

• If the humidifier must be located higher

than the dispersion assembly, use the
recommended installation shown in Figure
29-1.

Dispersion:

CONDENSATE RETURN GUIDELINES

To prevent overﬁ lling the steam cylinder, follow the condensate guidelines
below:

• When condensate can be returned to the steam cylinder:

– Single dispersion tube

– Up to 20 lbs/hr (9.1 kg/h) of steam production

– 10' (3 m) or less of steam hose between humidiﬁ er and dispersion

– 20' (6 m) or less of tubing between humidiﬁ er and dispersion

• When condensate should be wasted to the drain:

– Ultra-sorb or Rapid-sorb dispersion

– Single dispersion tube with condensate drain

– Single dispersion tube with:

- More than 20 lbs/hr (9.1 kg/h) or more of steam production, or

- More than 10' (3 m) of steam hose between humidiﬁ er and

dispersion

- More than 20' (6 m) of tubing between humidiﬁ er and dispersion

Returning condensate to steam cylinder

«
...
24
25
26
27
28
...
»

Содержание XT Series





































































Отзывы:

Нет отзывов

Похожие инструкции для XT Series

Бренд: Allonge Страницы: 48

Бренд: GMC Страницы: 20

Бренд: German pool Страницы: 16

Бренд: Artel Страницы: 24

Бренд: Lacidoll Страницы: 35

Бренд: Trotec Страницы: 18

Бренд: Whirlpool Страницы: 4

Бренд: Whirlpool Страницы: 1

Бренд: Whirlpool Страницы: 12

Бренд: Whirlpool Страницы: 12

Бренд: Whirlpool Страницы: 14

Бренд: Whirlpool Страницы: 12

Бренд: Whirlpool Страницы: 16

Бренд: Whirlpool Страницы: 12

Бренд: Whirlpool Страницы: 12

Бренд: Whirlpool Страницы: 12

Бренд: Whirlpool Страницы: 12

Бренд: Whirlpool Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды