DriSteem XT Series Скачать руководство пользователя страница 19

Страница: 19 / 68

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

INSTALLATION

Piping:

Plastic tie

Condensate hose (purchased
separately from DriSteem)

Plastic tie

Hose clamp (provided)

Steam hose
(purchased separately
from DriSteem)

Hose clamp (provided)

To open drain or humidiﬁ er ﬁ ll cup.
Water seal is required, whether condensate is piped to
open drain or returned to humidiﬁ er ﬁ ll cup.

OM-7974

7” (178 mm) water seal

Notes:
• Maximum recommended distance between humidiﬁ er

and XT steam blower is 10’ (3 m).

• Models XTP 042 through 096 are not intended for use

with a steam blower.

OM-7975

7” (178 mm)

water seal

To open drain or
humidiﬁ er ﬁ ll cup.
Water seal is
required, whether
condensate is
piped to open
drain or returned
to humidiﬁ er ﬁ ll
cup.

Plastic tie

Condensate
hose
(purchased
separately
from DriSteem)

Hose clamps
(provided)

Steam hose
(purchased separately from DriSteem)

Hose clamp*

Plastic tie

Steam hose*

Stainless steel Y connector*

* Provided in optional connector

kit Part No. 191070-102

Hose clamp*

Model XTP 025 only

XT steam blowers

FIGURE 15-1: PIPING FROM XT SERIES HUMIDIFIER TO REMOTE XT STEAM BLOWER

Содержание XT Series





































































Результаты поиска

Содержание XT Series

Отзывы:

Похожие инструкции для XT Series

Бренды по названию

Популярные бренды

DriSteem XT Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание XT Series

Отзывы:

Похожие инструкции для XT Series

Бренды по названию

Популярные бренды