DriSteem XT Series Скачать руководство пользователя страница 56

Страница: 56 / 68

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Troubleshooting

DriSteem Technical Support

Have the following information ready when
calling Technical Support. See phone number
inside front cover of this manual.

Humidiﬁ er model number

_______________________________

Humidiﬁ er serial number

_______________________________

When issue began

_______________________________

Issue description

_______________________________

DRAIN VALVE ASSEMBLY MAINTENANCE

Perform the following procedure

only

if the procedure on Page 51 does not

resolve drain valve issues. See Figure 51-2.

1. Perform Steps 1 through 4 on Page 51.

2. Remove the three screws and washers securing drain cup plate to drain

cup.

3. Lift drain valve body/plate assembly off of drain cup.

4. Vacuum loose scale and debris out of drain cup.

5. Remove ground plate, and clean scale and debris from ground plate and

outlet of drain valve body.

6. Reassemble drain valve assembly: Fit mounting screws with washers, insert

them through drain cup plate, and tighten them into drain cup. See notes
in Figure 51-2.

7. Clean end of hose, and reconnect it to drain valve body with hose clamp.

Plug Molex plug into its mating wire harness plug.

8. See “Start-up procedure” on Page 48 if returning humidifier to

operation.

MODEL XTP TROUBLESHOOTING

Follow the procedure below to resolve issues with Model XTP humidiﬁ ers:

1. Review possible causes and recommended actions in Table 54-1.

2. Follow the Test mode procedure beginning on Page 56.

The Test mode procedure is intended to check the general function of Model
XTP humidiﬁ ers and components, and to help diagnose and resolve general
operational problems.

3. If Table 54-1 and the Test mode procedure do not help you solve the issue,

call DriSteem (see inset at right) with the following information available:
• Humidiﬁ er model number and serial number (see nameplate on side of

the humidiﬁ er and steam blower)

•

Issue description

Example: water leaking, low humidity, high humidity, etc.

• When issue began

Example: After maintenance, cylinder replacement, etc.

• System

changes

Example: Pressure, new service, new controller, relocation, change in
maintenance, etc.

MAINTENANCE

Содержание XT Series





































































Результаты поиска

Содержание XT Series

Отзывы:

Похожие инструкции для XT Series

Бренды по названию

Популярные бренды

DriSteem XT Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание XT Series

Отзывы:

Похожие инструкции для XT Series

Бренды по названию

Популярные бренды