DriSteem XT Series Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 68

background image

49

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Maintenance:

SCHEDULED MAINTENANCE

At 1000-hour intervals or when “Service interval reached”
appears in the Messages Log, inspect the steam cylinder,
ﬁ ll and drain valves, steam hose, condensate piping,
water supply piping, drain piping, drain, and all other
parts for proper operation and cleaning requirements.
Verify proper operation of the high limit humidistat, relays,
and airﬂ ow proving switch.

STEAM CYLINDER SERVICE LIFE

Steam cylinder service life depends on operating hours
and water hardness. If “Check cylinder” appears in
the Messages Log during and shortly after start-up, the
message can be cleared and will stop repeating after a
few drain and ﬁ ll cycles.

When “Check cylinder” appears in the Messages Log
after extended operation, the humidiﬁ er will continue
to run, but the cylinder must be replaced to ensure
optimum output. Sure signs that a cylinder needs to be replaced are when it
is approximately one-third full of minerals, or minerals have bridged between
electrodes.

To replace the steam cylinder, ﬁ rst follow the cool-down procedure below.

COOL-DOWN PROCEDURE

1. In Vapor-logic keypad/display Main menu, select Tank Status, and press

Enter.

2. Select Mode, and press Enter.

3. Select Drain, and press Enter.

4. Let steam cylinder drain for 5 to 10 minutes (drain water is automatically

tempered when drain water tempering is selected).

5. Close field-installed manual supply water shut-off valve, and allow cylinder

to continue draining.

WARNING

Shutdown procedure

To prevent severe personal injury or death from electrical
shock, follow this shutdown procedure before performing
service or maintenance procedures on this humidiﬁ er (after
cylinder is drained and cooled):

1.

Use Vapor-logic keypad/display to drain cylinder.

2.

Use Vapor-logic controller keypad/display to change
control mode to Standby.

3.

Shut off all electrical power to humidiﬁ er using ﬁ eld-
installed fused disconnect, and lock all power disconnect
switches in OFF position.

Note:

Two-cylinder XT Series humidiﬁ ers have two power

supply connections.

4.

Close ﬁ eld-installed manual water supply shut-off valve.

WARNING

Hot water system

Cylinder and any undrained water may
be hot. To avoid injury from hot water,
follow the cool-down procedure before
proceeding with maintenance.

MAINTENANCE

Shutdown and cool-down procedures

«
...
51
52
53
54
55
...
»

Содержание XT Series





































































Отзывы:

Нет отзывов

Похожие инструкции для XT Series

Бренд: GMC Страницы: 20

Бренд: German pool Страницы: 16

pM-BP25 Pro S/T

Бренд: Plusmed Страницы: 40

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 3

Бренд: Sealey Страницы: 3

Бренд: Sealey Страницы: 3

Бренд: Sealey Страницы: 4

Бренд: Sealey Страницы: 4

Бренд: Sealey Страницы: 4

Бренд: Sealey Страницы: 4

Бренд: Sealey Страницы: 4

Бренд: Sealey Страницы: 4

Бренд: Sealey Страницы: 5

Бренд: Sealey Страницы: 5

Бренд: Sealey Страницы: 5

Бренд: Sealey Страницы: 5

Бренд: Sealey Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды