DriSteem XT Series Скачать руководство пользователя страница 15

Страница: 15 / 68

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

INSTALLATION

Fill cup extension kit

OM-7971-XT

Fill valve adapter

Overﬂ ow
elbow

Drain cup
plate

Supply
water
hose (A)

Cylinder ﬁ ll
hose (B)

Overﬂ ow
hose (C)

Fill cup
(see inset below)

OM-7629

Cylinder ﬁ ll (B)

Supply water (A)

Overﬂ ow (C)

Fill cup

Cylinder ﬁ ll hose
connection

A ﬁ ll cup extension (Figure 11-1) is required for the following:

• All XT Series humidiﬁ ers using Ultra-sorb or Rapid-sorb

• When developed length of steam tubing is more than 20' (6 m) and duct

static pressure exceeds 2" wc (498 Pa)

REMOVING EXISTING FILL CUP

Remove the existing ﬁ ll cup as follows:

1. Remove steam cylinder from XT cabinet (if not already out).

2. Expand spring clamps and slide them up cylinder fill hose and supply

water hose, and disconnect hoses from cylinder fill hose connection and
fill valve adapter.

3. Disconnect overflow hose from overflow elbow.

4. Remove fill cup and hoses (fill cup is press fit into top of XT cabinet).

INSTALLING FILL CUP EXTENSION KIT

1. Remove steam cylinder(s) from XT cabinet (if not already out).

2. Route fill cup extension kit hoses into cabinet through fill cup hole, and

fasten extension bracket as shown with two screws provided.

3. Route hoses along back of cabinet interior to provide clearance for

cylinder.

4. Cut supply water hose (small-diameter hose) (A) to length so it can attach

to fill valve adapter without kinking.

5. Expand spring clamp and slide it onto supply water hose (A) far enough

so it will not interfere, then push hose onto fill valve adapter. Expand and
slide spring clamp into place.

6. Cut cylinder fill hose (bottom, center hose) (B) to length so it can attach to

cylinder fill hose connection without kinking.

7. Expand spring clamp and slide it onto cylinder fill hose (B) far enough

so it will not interfere, then push hose onto cylinder fill hose connection.
Expand and slide spring clamp into place.

8. Cut overflow hose (C) to length so it can attach to overflow elbow

without kinking.

9. Push overflow hose onto overflow elbow. Spring clamp is not required on

this connection.

FIGURE 11-1: FILL CUP EXTENSION KIT

1" air gap

Содержание XT Series





































































Результаты поиска

Содержание XT Series

Отзывы:

Похожие инструкции для XT Series

Бренды по названию

Популярные бренды

DriSteem XT Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание XT Series

Отзывы:

Похожие инструкции для XT Series

Бренды по названию

Популярные бренды