DriSteem XT Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 68

background image

28

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

OM-7680

Connecting to humidifier with tubing

Important:

Failure to follow the recommendations in this
section can result in excessive back pressure on
the humidiﬁ er. This will result in unacceptable
humidiﬁ cation system performance such as
leaking gaskets, blown water seals, erratic
water level control, and spitting condensate
from dispersion tubes.

See Figures 31-1 and 32-1 for interconnecting tubing pitch requirements
for single dispersion tube applications. See Table 34-3 for interconnecting
tubing pitch requirements for Rapid-sorb applications.

• Support tubing between the humidiﬁ er steam outlet and the dispersion

system with pipe hangers. Failure to properly support the entire tubing
weight may cause damage to the humidiﬁ er tank and void the warranty.

• Ground metal steam tubing. See “Grounding steam tubing” at right.

• 90° elbows are not recommended. DriSteem recommends 90° long

sweeps. Two 45° elbows, 1' (0.3 m) apart may also be used.

• Insulating tubing reduces the loss in output caused by condensation.

• If ﬂ ux or any other surface preparation material is used when connecting

steam tubing and ﬁ ttings, drain and ﬁ ll the steam cylinder two times after
the ﬁ rst half hour of steam production:

– Model XTP, step 5 on page 48

This will minimize the possibility of foaming in the steam cylinder.

Grounding steam tubing

The XT Series humidiﬁ er has built-in functionality
for detecting and eliminating foaming in
the steam cylinder. However, because brief
periods of foaming are possible, grounding
metal steam tubing back to the humidiﬁ er earth
ground lug is necessary. This earth ground
will prevent foam from creating an electrically
conductive path from the electrically charged
cylinder water to the metal steam tubing.

XT Series humidiﬁ er

Pitch

To dispersion assembly

Tubing drip tee

8" (200 mm) recommended

6" (150 mm)

recommended

Open funnel or ﬂ oor drain

1" (25 mm)
air gap

3/4" (DN20)

Pitch

Insulate tubing to reduce steam loss

90° long sweep or two 45° elbows

FIGURE 28-1: DETAIL OF VERTICAL RISER DRIPS

INSTALLATION

Dispersion:

«
...
30
31
32
33
34
...
»

Содержание XT Series





































































Отзывы:

Нет отзывов

Похожие инструкции для XT Series

Бренд: Haier Страницы: 28

Бренд: NANO Страницы: 64

Бренд: Dantherm Страницы: 12

Airtek SMART CYCLE PLUS 100

Бренд: Parker Страницы: 45

Бренд: Gardner Denver Страницы: 36

Бренд: Airvana Страницы: 17

Бренд: Clear Safe Product Страницы: 12

Бренд: N'oveen Страницы: 9

Бренд: Microban Страницы: 11

Бренд: Dri-Eaz Страницы: 11

Бренд: XPower Страницы: 60

Бренд: Kenmore Страницы: 16

Бренд: Kenmore Страницы: 32

758.144071 Quiet comfort

Бренд: Kenmore Страницы: 16

Бренд: Kenmore Страницы: 16

Бренд: Kenmore Страницы: 36

Бренд: Kenmore Страницы: 36

2.0 & 3.5 gallon warm mist humidifier 997.151230

Бренд: Kenmore Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды