DriSteem XT Series Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 68

background image

35

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Rapid-sorb with Models XTP 025 through 048

OM-7696

Duct

XT Series humidiﬁ er

Air

ﬂ ow

Slip coupling or hose cuff

90° long sweep
or two 45° elbows

3/4" (DN20) copper

6" (150 mm)

recommended

Header pitch:
1/8"/ft (1%)
minimum

1" (25 mm) air gap

5" (125 mm) recommended

Condensate drain:
3/4" pipe thread (DN20)

Support bracket has
0.421" (11 mm)
mounting holes at top,
bottom, and end)

• 2"/ft (15%) when using steam hose

• ¼"/ft (2%) when using 2" tubing

Notes:
1. Use a hose cuff and clamps to connect steam outlet to tubing.
2. See installation procedure on Page 37.
3. Dashed lines indicate provided by installer.

Open drain required:
Locate air gap only in spaces with adequate
temperature and air movement to absorb ﬂ ash
steam; otherwise, condensation may form on nearby
surfaces. Refer to governing codes for drain pipe size
and maximum discharge water temperature.

Tubing must be grounded.
Insulate tubing to reduce
steam loss. See Tables
26-1 and 27-1 for
maximum tubing lengths.
See Notes.

L-bracket. Install with ﬂ ange facing upstream direction of airﬂ ow.
Drawing shows L-bracket correctly positioned for airﬂ ow.

Dispersion tube. Orient with tubelets perpendicular to airﬂ ow.

Secure and seal
escutcheon plates.

WARNING

Hot surface and steam hazard

Dispersion assembly and steam hose or tubing can contain steam, and surfaces can be hot. Discharged steam is not visible.
Contact with hot surfaces or air into which steam has been discharged can cause severe personal injury.

FIGURE 35-1: RAPID-SORB IN A HORIZONTAL AIRFLOW WITH HEADER INSIDE THE DUCT

INSTALLATION

Dispersion:

«
...
37
38
39
40
41
...
»

Содержание XT Series





































































Отзывы:

Нет отзывов

Похожие инструкции для XT Series

Бренд: Sandstrom Страницы: 36

Бренд: Macally Страницы: 5

Бренд: Condair Страницы: 72

Бренд: Quincy Страницы: 92

Бренд: Cooper & Hunter Страницы: 28

Бренд: Condair Страницы: 44

All Climate LAD250

Бренд: Breville Страницы: 16

Бренд: BRAYER Страницы: 36

Бренд: UFESA Страницы: 40

Бренд: ionmax Страницы: 16

Бренд: Kolin Страницы: 8

Simplicity SDR506RH

Бренд: Danby Страницы: 28

DRY 300 PLASTIK

Бренд: MICROWELL Страницы: 33

Бренд: Elsteam Страницы: 12

Бренд: Stadler Form Страницы: 25

Бренд: HAEGER Страницы: 56

DD122EA CLASSIC

Бренд: EcoSeb Страницы: 10

DD322EA CLASSIC

Бренд: EcoSeb Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды