Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 160

Страница: 160 / 363

160 Alphabetical list of commands

Elem Status

A standard SES status for the element:

•

Disabled

: Critical condition is detected.

•

Error

: Unrecoverable condition is detected. Appears only if there is a firmware problem related

to PHY definition data.

•

Non-critical

: Non-critical condition is detected.

•

Not Used

: Element is not installed in enclosure.

•

: Element is installed and no error conditions are known.

•

Unknown

: Either:

• Sensor has failed or element status is not available. Appears only if an I/O module indicates

it has fewer PHYs than the reporting I/O module, in which case all additional PHYs are

reported as unknown.

• Element is installed with no known errors, but the element has not been turned on or set into

operation.

Disabled

•

Enabled

: PHY is enabled.

•

Disabled

: PHY is disabled.

Reason

•

Blank if

Elem Status

•

Error count interrupts

: PHY disabled because of error-count interrupts.

•

Phy control

: PHY disabled by a SES control page as a result of action by a Storage

Controller or user.

•

Not ready

: PHY is enabled but not ready. Appears for SC-1 PHYs when the partner I/O

module is not installed. Appears for Drive, SC-1, or Ingress PHYs when a connection problem

exists such as a broken connector.

•

Drive removed

: PHY disabled because drive slot is empty.

•

Unused - disabled by default

: PHY is disabled by default because it is not used.

•

Excessive Phy changes

: PHY is disabled because of excessive PHY change counts.

Example

Show expander status for each enclosure.

# show expander-status

Basetypes •

sas-status-controller-a

•

sas-status-drawer

•

status

Содержание AssuredSAN 6004












































































































































































































































































































































































Результаты поиска

Содержание AssuredSAN 6004

Отзывы:

Dot Hill Systems AssuredSAN 6004, Справочное руководство CLI, Страница: 160 / 363

Результаты поиска

Содержание AssuredSAN 6004

Отзывы: