Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 259

Страница: 259 / 363

drive-parameters 259

drive-parameters

This basetype is used by

show disk-parameters

Table 26

drive-parameters properties

Name

Type

Description

smart

string

Shows whether SMART (Self-Monitoring Analysis and Reporting Technology) is

enabled or disabled for disks.

•

Detect-Only

: Each disk in the system retains its individual SMART setting,

as will new disks added to the system.

•

Enabled

: SMART is enabled for all disks in the system and will be enabled

for new disks added to the system.

•

Disabled

: SMART is disabled for all disks in the system and will be

disabled for new disks added to the system.

smart-numeric

uint32

Numeric equivalents for

smart

values.

•

0: Detect-Only

•

1: Enabled

•

2: Disabled

drive-write-

back-cache

string

•

Disabled

: Disk write-back cache is disabled for all disks in the system and

will be enabled for new disks added to the system. This parameter cannot be

changed.

drive-write-

back-cache-

numeric

uint32

Numeric equivalents for

drive-write-back-cache

values.

•

0: Detect-Only

•

1: Enabled

•

2: Disabled

drive-timeout-

retry-max

uint8

Maximum number of times a timed-out I/O operation can be retried before the

operation is failed.

drive-attempt-

timeout

uint8

Number of seconds before an I/O operation is aborted and possibly retried.

drive-overall-

timeout

uint8

Total time in seconds before an I/O operation is failed regardless of the

drive-attempt-timeout

and

drive-timeout-retry-max

settings.

disk-dsd-enable

string

Shows whether available disks and global spares will spin down after a period

of inactivity shown by the

disk-dsd-delay

property.

•

Disabled

: Drive spin down for available disks and global spares is

disabled.

•

Enabled

: Drive spin down for available disks and global spares is

enabled.

disk-dsd-

enable-numeric

uint32

Numeric equivalents for

disk-dsd-enable

values.

•

0: Disabled

•

1: Enabled

disk-dsd-

enable-pool

string

Not applicable.

disk-dsd-delay

uint16

Shows the period of inactivity in minutes after which available disks and global

spares will spin down, from 1 to 360 minutes. The value 0 means spin down is

disabled.

Содержание AssuredSAN 6004












































































































































































































































































































































































Результаты поиска

Содержание AssuredSAN 6004

Отзывы:

Dot Hill Systems AssuredSAN 6004, Справочное руководство CLI, Страница: 259 / 363

Результаты поиска

Содержание AssuredSAN 6004

Отзывы: