Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 363

Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 108

108 Alphabetical list of commands

set network-parameters

Description

Sets parameters for controller module network ports.
You can manually set static IP values for each controller, or you can specify that IP values should be

set automatically for both controllers through communication with a Dynamic Host Configuration

Protocol (DHCP) server.
Each controller has the following factory-default IP settings:

•

DHCP: disabled

•

Controller A IP address: 10.0.0.2

•

Controller B IP address: 10.0.0.3

•

IP subnet mask: 255.255.255.0

•

Gateway IP address: 10.0.0.1

When DHCP is enabled, the following initial values are set and remain set until the system is able to

contact a DHCP server for new addresses.

•

Controller IP addresses: 169.254.x.x (where the value of

x.x

is the lowest 16 bits of the controller

serial number)

•

IP subnet mask: 255.255.0.0

•

Gateway IP address: 0.0.0.0

169.254.

x.x

addresses (including gateway 169.254.0.1) are on a private subnet that is reserved for

unconfigured systems and the addresses are not routable. This prevents the DHCP server from

reassigning the addresses and possibly causing a conflict where two controllers have the same IP

address. As soon as possible, change these IP values to proper values for your network.
To switch a controller from DHCP addressing to static addressing, you must set the IP address,

netmask, and gateway values.

NOTE:

The following IP addresses are reserved for internal use by the storage system:

192.168.200.253, 192.168.200.254, 172.22.255.253, 172.22.255.254, and 127.x.x.x.

Min. role

manage

Syntax

set network-parameters

[controller a|b]

[dhcp]

[gateway

gateway

]

[ip

address

]

[ipv 4|6]

[netmask

netmask

]

[ping-broadcast enabled|disabled|on|off]

Parameters

controller a|b

Optional. For IP-related parameters, this specifies whether to apply settings to controller A or B. If this

parameter is omitted, settings are applied to the controller being accessed. This parameter does not

apply to Ethernet switch-related parameters, whose settings are always applied to the controller

being accessed.

dhcp

Optional. Specifies to use DHCP to set both controllers’ IP values.

gateway

gateway

Optional. A gateway IP address for the port.

ip

address

Optional. An IP address for the port.

«
...
106
107
108
109
110
...
»

Содержание AssuredSAN 6004












































































































































































































































































































































































Отзывы:

Нет отзывов