Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 223

Страница: 223 / 363

advanced-settings-table 223

dynamic-spares

string

Shows whether the storage system will automatically use a compatible disk as a

spare to replace a failed disk in a vdisk if no compatible spare is available.

•

Disabled

: The dynamic spares feature is disabled. This is the default.

•

Enabled

: The dynamic spares feature is enabled.

emp-poll-rate

uint32

Shows the interval in seconds at which the storage system will poll each

enclosure's Enclosure Management Processor (EMP) for status changes, from 5

to 3600 seconds. The default is 5 seconds.

host-cache-

control

string

Shows whether hosts are allowed to use the

SCSI MODE SELECT

command to

change the storage system's write-back cache setting.

•

Disabled

: Host control of caching is disabled. This is the default.

•

Enabled

: Host control of caching is enabled.

host-cache-

control-numeric

uint32

Numeric equivalents for

host-cache-control

values.

•

0: Disabled

•

1: Enabled

sync-cache-mode

string

Shows how the

SCSI SYNCHRONIZE CACHE

command is handled.

•

Immediate

: Good status is returned immediately and cache content is

unchanged. This is the default.

•

Flush To Disk

: Good status is returned only after all write-back data for

the specified volume is flushed to disk.

sync-cache-

mode-numeric

uint32

Numeric equivalents for

sync-cache-mode

values.

•

0: Immediate

•

1: Flush to Disk

independent-

cache

string

Shows the cache redundancy mode for a dual-controller storage system.

•

Disabled

: Controller failover is enabled and data in a controller’s write-

back cache is mirrored to the partner controller.

•

Enabled

: The controllers use Independent Cache Performance Mode, in

which controller failover is disabled and data in a controller’s write-back

cache is not mirrored to the partner controller. This improves write

performance at the risk of losing unwritten data if a controller failure occurs

while there is data in controller cache.

independent-

cache-numeric

uint32

Numeric equivalents for

independent-cache

values.

•

0: Disabled

•

1: Enabled

missing-lun-

response

string

Shows whether host drivers may probe for LUNs until the host drivers reach the

LUN to which they have access.

•

Not Ready

: Sends a reply that there is a LUN where a gap has been

created but that it’s “not ready.” Sense data returned is sensekey = 2, code =

4, qualifier = 3. This is the default.

•

Illegal Request

: Sends a reply that there is a LUN but that the request

is “illegal.” Sense data returned is sensekey = 5, code = 25h, qualifier = 0.

missing-lun-

response-

numeric

uint32

Numeric equivalents for

missing-lun-response

values.

•

0: Not Ready

•

1: Illegal Request

controller-

failure

string

Shows whether the cache policy will change from write-back to write-through

when a controller fails.

•

Disabled

: The controller failure trigger is disabled. This is the default.

•

Enabled

: The controller failure trigger is enabled.

Table 8

advanced-settings-table properties (continued)

Name

Type

Description

Содержание AssuredSAN 6004












































































































































































































































































































































































Результаты поиска

Содержание AssuredSAN 6004

Отзывы:

Dot Hill Systems AssuredSAN 6004, Справочное руководство CLI, Страница: 223 / 363

Результаты поиска

Содержание AssuredSAN 6004

Отзывы: