Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 264

Страница: 264 / 363

264 XML API basetype properties

drive-down-code

uint8

Numeric code indicating why the disk is down.

owner

string

Current owner, which is either the preferred owner during normal operation or

the partner controller when the preferred owner is offline.

•

: Controller A.

•

: Controller B.

owner-numeric

string

Numeric equivalents for

owner

values.

•

0: B

•

1: A

index

uint32

For internal use only.

rpm

uint32

The speed of a spinning disk, in thousands of revolutions per minute, as

specified by the disk vendor. For an SSD, 0 is shown.

size

string

Disk capacity, formatted to use the current base, precision, and units.

size-numeric

string

Unformatted

size

value in 512-byte blocks.

transfer-rate

string

Disk data transfer rate in Gbit/s. It is normal behavior for the rate to vary.

•

1.5

•

3.0

•

6.0

Some 6-Gbit/s disks might not consistently support a 6-Gbit/s transfer rate. If

this happens, the controller automatically adjusts transfers to those disks to

3 Gbit/s, increasing reliability and reducing error messages with little impact on

system performance. This rate adjustment persists until the controller is restarted

or power-cycled.

transfer-rate-

numeric

uint32

For internal use only.

attributes

string

Shows which controller a single-ported disk is connected to.

•

: Controller A.

•

: Controller B.

attributes-

numeric

uint32

For internal use only.

enclosure-wwn

string

Enclosure WWN.

status

string

Disk status.

•

: The disk is present and is properly communicating with the expander.

•

Spun Down

: The disk is present and has been spun down by the drive spin

down feature.

•

Warning

: The disk is present but the system is having communication

problems with the disk LED processor. For disk and midplane types where

this processor also controls power to the disk, power-on failure will result in

Error

status.

•

Error

: The disk is present but is not detected by the expander.

•

Unknown

: Initial status when the disk is first detected or powered on.

•

Not Present

: The disk slot indicates that no disk is present.

•

Unrecoverable

: The disk is present but has unrecoverable errors.

•

Unavailable

: The disk is present but cannot communicate with the

expander.

•

Unsupported

: The disk is present but is an unsupported type.

Table 28

drives properties (continued)

Name

Type

Description

Содержание AssuredSAN 6004












































































































































































































































































































































































Результаты поиска

Содержание AssuredSAN 6004

Отзывы:

Dot Hill Systems AssuredSAN 6004, Справочное руководство CLI, Страница: 264 / 363

Результаты поиска

Содержание AssuredSAN 6004

Отзывы: