Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 156

Страница: 156 / 363

156 Alphabetical list of commands

EMP

controller-ID

CH:ID Rev

The channel ID and firmware revision of the drawer's Enclosure Management Processor for controller

module A's Expander Controller.

Status

Status of the drawer.

•

Warning

•

Error

•

Unknown

•

Unavailable

•

Not Present

Health

•

Degraded

•

Fault

•

N/A

•

Unknown

Reason

If Health is not

, this field shows the reason for the health state.

Action

If Health is not

, this field shows recommended actions to take to resolve the health issue.

Example

Show information about all enclosures in the system.

# show enclosures

Basetypes •

enclosures

•

status

Содержание AssuredSAN 6004












































































































































































































































































































































































Результаты поиска

Содержание AssuredSAN 6004

Отзывы:

Dot Hill Systems AssuredSAN 6004, Справочное руководство CLI, Страница: 156 / 363

Результаты поиска

Содержание AssuredSAN 6004

Отзывы: