Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 92

Страница: 92 / 363

Alphabetical list of commands

set controller-date

Description

Sets the date and time parameters for the system. You can set the date and time manually or

configure the system to communicate with a Network Time Protocol (NTP) server. Alternatively, you

can configure NTP by using the

set ntp-parameters

command.

NOTE:

If you specify valid NTP parameters and manual date/time parameters in the same

command, the NTP parameters will take precedence. If the NTP server cannot be contacted, the date

and time will not be changed and no error message will be displayed.If you specify the

timestamp

parameter and other manual date/time parameters in the same command, the

timestamp

parameter will take precedence.

Min. role

manage

Syntax

To set the date and time manually:

set controller-date

jan|feb|mar|apr|may|jun|jul|aug|sep|oct|nov|dec

day

year

To set the date and time manually by specifying a timestamp:

set controller-date

timestamp

timestamp

ti|-

]

To configure use of NTP:

set controller-date

ntp enabled|disabled|on|off

ntpaddress

IP-address

ti|-

]

Parameters

jan|feb|mar|apr|may|jun|jul|aug|sep|oct|nov|dec

The month.

day

The day number (1–31).

The hour (0–23), the minutes (0–59), and the seconds (0–59).

year

The year as a four-digit number.

ntp enabled|disabled|on|off

Enables or disables use of NTP. When NTP is enabled and the specified NTP server is available,

each controller’s time is synchronized with the server.

ntpaddress

IP-address

The network address of an available NTP server.

ti|-

]

The system’s time zone as an offset in hours (-12 t14) and optionally minutes (00–59) from

Coordinated Universal Time (UTC). To specify a positive offset, the '+' is optional. To specify a

negative offset, the '-' is required. The hour value can have one or two digits and can omit a leading

zero. If the minutes value is specified it must have two digits. If it is omitted, the minutes value is set to

00.

Содержание AssuredSAN 6004












































































































































































































































































































































































Результаты поиска

Содержание AssuredSAN 6004

Отзывы:

Dot Hill Systems AssuredSAN 6004, Справочное руководство CLI, Страница: 92 / 363

Результаты поиска

Содержание AssuredSAN 6004

Отзывы: