Dionex ICS-3000 Скачать руководство пользователя страница 236 | Manualshive

Страница: 236 / 392

background image

ICS-3000 Ion Chromatography System

220

Doc. 065031-04 1/08

3. If you suspect a malfunction in the suppressor controller, contact Dionex

for assistance.

NOTE The ICS-3000 Ion Chromatography System electronics

components cannot be serviced by the user.

This error appears when, in order to maintain the selected current, the ICS-
3000 Ion Chromatography System is required to apply a higher voltage than
the suppressor can support.

To troubleshoot:

1. Reduce the flow rate.

2. Rehydrate the suppressor. Refer to the suppressor manual for instructions.

Suppressor manuals are included on the Dionex Reference Library CD-
ROM (P/N 053891).

3. If the error persists, replace the suppressor (see

This error appears if you turn on the suppressor and the system cannot
establish a connection with the suppressor.

To troubleshoot:

1. Check the suppressor cable connection.

2. If the error persists, replace the suppressor (see

Suppressor 1 over-power.

-or-

Suppressor 2 over-power.

Suppressor 1 over-voltage.

-or-

Suppressor 2 over-voltage.

«
...
234
235
236
237
238
...
»

Содержание ICS-3000









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ICS-3000

Бренд: Varec Страницы: 74

Бренд: Halyard Страницы: 84

Бренд: PAIDI Страницы: 48

Бренд: MacDon Страницы: 89

Бренд: Yates Страницы: 2

Бренд: Pari Страницы: 50

Бренд: Icare Страницы: 42

Бренд: Raytheon Страницы: 68

Бренд: KegLand Страницы: 23

Бренд: MAHA Страницы: 21

Бренд: MAGUIRE Страницы: 47

Бренд: OAKWORKS Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: O2matic Страницы: 4

Бренд: Yuwell Страницы: 2

Бренд: Zennio Страницы: 3

Бренд: JBM Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды