Dionex ICS-3000 Скачать руководство пользователя страница 130 | Manualshive

Страница: 130 / 392

background image

ICS-3000 Ion Chromatography System

114

Doc. 065031-04 1/08

•

If you select a low flow rate that allows the system pressure to drop
below 14 MPa (2000 psi) and you do not turn off the EG, the EG will
continue to generate eluent at the concentration set for the last step of
the last Chromeleon or Chromeleon Xpress program.

If this occurs, the eluent concentration will increase in proportion to
the decrease in the flow rate. In extreme cases, excessive heat buildup
can occur and damage the EluGen cartridge.

•

For a complete list of operating precautions for EluGen cartridges and
CR-TC trap columns, refer to the product manuals. The manuals are
provided on the Dionex Reference Library CD-ROM (P/N 053891).

DO NOT CAP THE WASTE CONTAINER: The ICS-3000 Eluent
Generator (EG), Atlas Electrolytic Suppressor, and Self-Regenerating
Suppressor (SRS) use an electrolytic process that results in the
production of small amounts of oxygen or hydrogen gas. To ensure
that the gas is not trapped in a closed container and allowed to
concentrate, install a 1.3-cm (0.52-in) ID black gas separator waste
tube (P/N 045460) in an uncapped waste container. Connect the
Waste, Gas Separator line to the waste tube.

NE FERMEZ PAS LE CONTENEUR DE GAZ RÉSIDUEL: Le ICS-3000
Eluent Generator (EG), le Atlas Electrolytic Suppressor, et le Self-
Regenerating Suppressor (SRS) travaillent avec un proces
d´électrolyse, qui produit des petites quantités de gaz d´oxygène ou
d´hydrogène. Afin de garantir que le gaz ne soit pas enfermé dans un
conteneur fermé et puisse s´y concentrer, connectez un tube noir à
gaz résiduel (diamètre intérieur = 1,3 cm; n° de commande 045460) à
un conteneur ouvert (non fermé). Connectez le conteneur résiduel au
tube résiduel/gaz séparateur (désigné: « Waste, Gas Separator»).

VERSCHLIESSEN SIE DEN ABFALLBEHÄLTER NICHT: Der ICS-3000
Eluent Generator (EG), Atlas Electrolytic Suppressor und Self-
Regenerating Suppressor (SRS) verwenden einen Elektrolyseprozess,
wodurch kleine Mengen an Sauerstoff und Wasserstoff entstehen.
Führen Sie einen schwarzen Gasabscheiderschlauch (ID = 1,3 cm;
Bestell-Nr. 045460) in einen offenen (unverschlossenen)
Abfallbehälter, damit sich das Gas nicht in einem geschlossenen
Behälter sammelt und aufkonzentriert. Verbinden Sie die mit Waste,
Gas Separator bezeichnete Leitung mit dem Abfallschlauch.

«
...
128
129
130
131
132
...
»

Содержание ICS-3000









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ICS-3000

Бренд: Waterwise Страницы: 12

Бренд: ParaBody Страницы: 38

Litmann Quality 3100

Бренд: 3M Страницы: 2

Бренд: ACCU-CHECK Страницы: 104

Бренд: Baoding Longer Precision Pump Страницы: 6

FreeStyle Comfort

Бренд: CAIRE Страницы: 33

Бренд: Ocmis Irrigazione Страницы: 100

Бренд: Unitary products group Страницы: 28

Бренд: Nitecore Страницы: 4

Бренд: Halyard Страницы: 88

Бренд: HALDER Страницы: 2

Бренд: jablotron Страницы: 2

Бренд: Keithley Страницы: 79

Бренд: Kayakpro Страницы: 17

Бренд: Yoshitake Страницы: 11

Бренд: WalkMed Страницы: 2

Бренд: Walinga Страницы: 20

Бренд: Össur Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды