Dell Force10 MXL Blade Скачать руководство пользователя страница 188

Страница: 188 / 732

188

Dynamic Host Configuration Protocol (DHCP)

www.dell.com | support.dell.com

clear ip dhcp

Reset DHCP counters.

Syntax

clear ip dhcp [binding {

address

}

| conflict | server statistics]

Parameters

Command Mode

EXEC Privilege

Default

none

Command

History

Usage

Information

Entering <CR> after

clear ip dhcp binding

, clears all the IPs from the binding table.

debug ip dhcp server

Display FTOS debugging messages for DHCP.

Syntax

debug ip dhcp server [events | packets]

Parameters

Command Mode

EXEC Privilege

Default

none

Command

History

default-router

Assign a default gateway to clients based on address pool.

Syntax

default-router

address

[

address2

...

address8

]

Parameters

Command Mode

DHCP <POOL>

binding

Enter this keyword to delete all entries in the binding table.

address

Enter the IP address to clear the binding entry for a single IP address.

conflict

Enter this keyword to delete all of the log entries created for IP address
conflicts.

server statistics

Enter this keyword to clear all the server counter information.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

events

Enter this keyword to display DHCP state changes.

packet

Enter this keyword to display packet transmission/reception.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

address

Enter the a list of routers that may be the default gateway for clients on the subnet. You may
specify up to 8. List them in order of preference.

Содержание Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Force10 MXL Blade

Отзывы:

Похожие инструкции для Force10 MXL Blade

Бренды по названию

Популярные бренды

Dell Force10 MXL Blade, Справочное руководство

Результаты поиска

Содержание Force10 MXL Blade

Отзывы:

Похожие инструкции для Force10 MXL Blade

Бренды по названию

Популярные бренды