Dell Force10 MXL Blade Скачать руководство пользователя страница 276 | Manualshive

Страница: 276 / 732

background image

276

|

Interfaces

www.dell.com | support.dell.com

Command

History

Usage

Information

This command is found on the 1000/10000 Base-T Ethernet interfaces.

When you enable

auto

, the system performs and automatic discovery to determine the optics installed

and configure the appropriate speed.

When you configure a speed for the 1000/10000 interface, you should confirm

negotiation auto

command setting. Both sides of the link should have auto-negotiation either enabled or disabled. For
speed settings of 1000 or auto, the software sets the link to auto-negotiation and you cannot change that
setting.

In FTOS, the command

speed 1000

is an exact equivalent of

speed auto 1000

in IOS.

Related

Commands

stack-unit portmode

Split a single 40G port into 4-10G ports on the MXL Switch.

Syntax

stack-unit

stack-unit

port

number

portmode quad

Parameters

Defaults

Disabled

Command Modes

CONFIGURATION

Command

History

Usage

Information

Splitting a 40G port into 4x10G port is supported only on a standalone unit.

•

Split ports cannot be used as stack-link to stack an

MXL Switch

.

•

Split ports MXL Switch unit cannot be a part of any stacked system.

•

The unit number with the split ports must be the default (stack-unit 0)

•

This can be verified using CLI “show system brief”. If the unit ID is different than 0, then it must
be renumbered to 0 before ports are split. By using the stack unit id renumber 0 command in
EXEC mode.

The quad port must be in a default configuration before it can be split into 4x10G ports. The 40G port
is lost in the config when the port is split, so be sure the port is also removed from other L2/L3 feature
configurations. The system must be reloaded after issuing the CLI for the change to take effect.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

duplex (1000/10000
Interfaces)

Configures duplex mode on physical interfaces with the speed set to 1000/
1000.

negotiation auto

Enables or disables auto-negotiation on an interface.

stack-unit

Enter the stack member unit identifier of the stack member to reset.

MXL Switch range

: 0 to 5

Note:

The MXL Switch commands accept Unit ID numbers 0-5, though MXL Switch

supports stacking up to 3 units only with FTOS version 8.3.7.1.

number

Enter the port number of the 40G port to be split.

MXL Switch range

: Enter one of the following port numbers: 48, 52, 56, or 60.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

«
...
274
275
276
277
278
...
»

Содержание Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Force10 MXL Blade

Univerge SV9300

Бренд: NEC Страницы: 47

Univerge SV9100

Бренд: NEC Страницы: 766

Бренд: LaCie Страницы: 4

88631SU - System x3850 - 8863

Бренд: IBM Страницы: 90

Бренд: Omega Страницы: 49

Бренд: Iwatsu Страницы: 338

SUPERSERVER 5018A-MHN4

Бренд: Supermicro Страницы: 116

BACnet/IP Server-SUNWAYS

Бренд: IntesisBox Страницы: 5

8676 - Eserver xSeries 335

Бренд: IBM Страницы: 172

Бренд: Belkin Страницы: 2

FIDATA HFAS1-S10U

Бренд: I-O DATA Страницы: 46

PRIMERGY Econel 230R S1

Бренд: Fujitsu Страницы: 53

Primergy ECONEL 100 S2

Бренд: Fujitsu Страницы: 8

PRIMERGY Econel 200 S2

Бренд: Fujitsu Страницы: 65

PRIMERGY MX130 S1

Бренд: Fujitsu Страницы: 85

PRIMERGY Econel 100

Бренд: Fujitsu Страницы: 64

Бренд: Fujitsu Страницы: 105

Бренд: Fujitsu Страницы: 142

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды