Dell Force10 MXL Blade Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 732

background image

100

|

Access Control Lists (ACL)

www.dell.com | support.dell.com

•

Use the

no

permit

{

source

[

mask

] |

any | host

ip-address

} command.

Parameters

Defaults

Not configured.

Command Modes

CONFIGURATION-IP ACCESS-LIST-STANDARD

Command

History

Usage

Information

The

order

option is relevant in the context of the Policy QoS feature only. For more information, refer

to the

Quality of Service (QoS)

chapter of the

FTOS Configuration Guide

.

In the MXL Switch, you can configure either count (packets) or count (bytes). However, for an ACL
with multiple rules, you can configure some ACLs with count (packets) and others as count (bytes) at
any given time

.

Related

Commands

seq

Assign a sequence number to a deny or permit filter in an IP access list while creating the filter.

Syntax

seq

sequence-number

{

deny

|

permit

} {

source

[

mask

] |

any

|

host

ip-address

}} [

count

[

byte

]

[

dscp

value

] [

order

]

[fragments]

Parameters

source

Enter the IP address in dotted decimal format of the network from which the
packet was sent.

mask

(OPTIONAL) Enter a network mask in /prefix format (/x) or A.B.C.D. The mask,
when specified in A.B.C.D format, may be either contiguous or non-contiguous.

any

Enter the keyword

any

to specify that all routes are subject to the filter.

host

ip-address

Enter the keyword

host

followed by the IP address to specify a host IP address

or hostname.

count

(OPTIONAL) Enter the keyword

count

to count packets processed by the filter.

dscp

(OPTIONAL) Enter the keyword

dscp

to match to the IP DSCP values.

byte

(OPTIONAL) Enter the keyword

byte

to count bytes processed by the filter.

order

(OPTIONAL) Enter the keyword

order

to specify the QoS priority for the ACL

entry.

Range:

0-254 (where 0 is the highest priority and 254 is the lowest; lower

order numbers have a higher priority)

Default:

If the order keyword is not used, the ACLs have the lowest order by
default (255).

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

deny

Assign an IP ACL filter to deny IP packets.

ip access-list standard

Create a standard ACL.

sequence-number

Enter a number from 0 to 4294967290.

Range: 0 to 65534

deny

Enter the keyword

deny

to configure a filter to drop packets meeting this

condition.

permit

Enter the keyword

permit

to configure a filter to forward packets meeting this

criteria.

«
...
98
99
100
101
102
...
»

Содержание Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Force10 MXL Blade

Express5800/180Ra-7

Бренд: NEC Страницы: 2

Express5800/120Rh-2

Бренд: NEC Страницы: 2

Express5800/120Rh-2

Бренд: NEC Страницы: 2

Express5800/120Rg-1

Бренд: NEC Страницы: 2

Express5800/120Rf-1

Бренд: NEC Страницы: 21

Express5800/120Ra-1

Бренд: NEC Страницы: 6

Express5800/120Mc2 series

Бренд: NEC Страницы: 2

EXPRESS5800/120Le

Бренд: NEC Страницы: 56

Express5800 320La

Бренд: NEC Страницы: 8

Express5800 120Li

Бренд: NEC Страницы: 2

Express5800 120Ed

Бренд: NEC Страницы: 29

Active Upgrade Express5800/320Fc

Бренд: NEC Страницы: 4

Бренд: NEC Страницы: 10

Express5800/120Rj-2

Бренд: NEC Страницы: 18

Express5800/120Rh-1

Бренд: NEC Страницы: 20

Bull NovaScale R620 Series

Бренд: NEC Страницы: 346

Express5800 320La

Бренд: NEC Страницы: 206

Express5800/R110j-1

Бренд: NEC Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды