Dell Force10 MXL Blade Скачать руководство пользователя страница 129

Страница: 129 / 732

Access Control Lists (ACL) |

129

Usage

Information

Prefix lists redistribute OSPF and RIP routes meeting specific criteria. For related RIP commands,
refer to

Chapter 26, Routing Information Protocol (RIP)

. For related OSPF commands supported, refer

FTOS Command Line Reference Guide

Chapter 21, Open Shortest Path First (OSPFv2)

Related

Commands

permit

Configure a filter that passes packets meeting the criteria specified.

Syntax

permit

ip-prefix

[

min-prefix-length

] [

max-prefix-length

]

Parameters

Command Modes

PREFIX-LIST

Command

History

Usage

Information

Sequence numbers for this filter are automatically assigned starting at sequence number 5.

If you do not use the options

, only packets with an exact match to the prefix are filtered.

Related

Commands

seq

Assign a sequence number to a deny or permit filter in a prefix list while configuring the filter.

Syntax

seq

sequence-number

{

deny

permit

} {

any

} | [

ip-prefix

/nn

{

min-prefix-length

} {

max-prefix-length

}

] | [

bitmask

number

]

Parameters

show ip route list

Displays IP routes in an IP prefix list.

show ip prefix-list summary

Displays a summary of the configured prefix lists.

ip-prefix

Specify an IP prefix in the network/length format. For example, 35.0.0.0/8
means match the first 8 bits of address 35.0.0.0.

min-prefix-length

(OPTIONAL) Enter the keyword

followed by the minimum prefix

length, which is a number from zero (0) to 32.

max-prefix-length

(OPTIONAL) Enter the keyword

followed by the maximum prefix length,

which is a number from zero (0) to 32.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

deny

Configures a filter to drop packets.

seq

Configures a drop or permit filter with a specified sequence number.

sequence-number

Enter a number.

Range: 1 to 4294967294.

deny

Enter the keyword

deny

to configure a filter to drop packets meeting this

condition.

permit

Enter the keyword

permit

to configure a filter to forward packets meeting this

condition.

any

(OPTIONAL) Enter the keyword

any

to match any packets.

ip-prefix /nn

(OPTIONAL) Specify an IP prefix in the network/length format. For example,
35.0.0.0/8 means match the first 8 bits of address 35.0.0.0.

Содержание Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Force10 MXL Blade

Отзывы:

Dell Force10 MXL Blade, Справочное руководство, Страница: 129 / 732

Результаты поиска

Содержание Force10 MXL Blade

Отзывы: