Dell Force10 MXL Blade Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 732

background image

Access Control Lists (ACL) |

103

Defaults

Not configured.

Command Modes

CONFIGURATION-IP ACCESS-LIST-EXTENDED

Command

History

Usage

Information

The

order

option is relevant in the context of the Policy QoS feature only. For more information, refer

to the

Quality of Service (QoS)

chapter of the

FTOS Configuration Guide

.

In the MXL Switch, you can configure either count (packets) or count (bytes). However, for an ACL
with multiple rules, you can configure some ACLs with count (packets) and others as count (bytes) at
any given time

.

Related

Commands

deny icmp

Configure a filter to drop all or specific ICMP messages.

Syntax

deny icmp

{

source mask

|

any

|

host

ip-address

} {

destination mask

|

any

|

host

ip-address

} [

dscp

]

[

message-type

] [

count

[

byte

]] [

order

] [

fragments

]

To remove this filter, you have two choices:

•

Use the

no

seq

sequence-number

command if you know the filter’s sequence number.

•

Use the

no

deny

icmp

{

source mask

|

any

|

host

ip-address

} {

destination mask

|

any

|

host

ip-address

} command.

Parameters

byte

(OPTIONAL) Enter the keyword

byte

to count bytes processed by the filter.

dscp

(OPTIONAL) Enter the keyword

dscp

to match to the IP DSCP values.

order

(OPTIONAL) Enter the keyword

order

to specify the QoS priority for the

ACL entry.

Range:

0-254 (where 0 is the highest priority and 254 is the lowest; lower

order numbers have a higher priority)

Default:

If the order keyword is not used, the ACLs have the lowest order by
default (255).

fragments

Enter the keyword

fragments

to use ACLs to control packet fragments.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

deny tcp

Assigns a filter to deny TCP packets.

deny udp

Assigns a filter to deny UDP packets.

ip access-list extended

Creates an extended ACL.

source

Enter the IP address of the network or host from which the packets were sent.

mask

Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in

A.B.C.D format, may be either contiguous or non-contiguous.

any

Enter the keyword

any

to specify that all routes are subject to the filter.

host

ip-address

Enter the keyword

host

followed by the IP address to specify a host IP address.

destination

Enter the IP address of the network or host to which the packets are sent.

dscp

Enter this keyword to deny a packet based on DSCP value.

Range: 0-63

«
...
101
102
103
104
105
...
»

Содержание Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Force10 MXL Blade

Бренд: IBM Страницы: 151

Бренд: Far south networks Страницы: 4

SUPERO SuperServer 6026TT-GIBQRF

Бренд: Supero Страницы: 104

Express5800/R120h-1E

Бренд: NEC Страницы: 52

Бренд: Hologic Страницы: 30

Бренд: MISUMI Страницы: 18

Бренд: Acard Страницы: 43

Бренд: Monoprice Страницы: 5

Бренд: Meinberg Страницы: 112

Бренд: TAG Страницы: 50

A+ SERVER 1022G-NTF

Бренд: Supero Страницы: 116

Бренд: Lantronix Страницы: 82

Бренд: Lantronix Страницы: 95

Бренд: Kommander Страницы: 124

Бренд: Mackie Страницы: 110

Бренд: Gateway Страницы: 135

Бренд: Oracle Страницы: 49

SuperServer 5019P-MT

Бренд: Supermicro Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды