Dell Force10 MXL Blade Скачать руководство пользователя страница 148 | Manualshive

Страница: 148 / 732

background image

148

|

Content Addressable Memory (CAM)

www.dell.com | support.dell.com

cam-acl (Configuration)

Select the default CAM allocation settings or reconfigure new CAM allocation for Layer 2, IPv4 and
IPv6 ACLs, Layer 2 and Layer 3 (IPv4) QoS, Layer 2 Protocol Tunneling (L2PT), IP and MAC source
address validation for DHCP, Ethernet Connectivity Fault Management (CFM) ACLs, and
Policy-based Routing (PBR).

Syntax

cam-acl

{

default

|

l2acl

number

ipv4acl

number

ipv6acl

number

ipv4qos

number

l2qos

number

l2pt

number

ipmacacl

number

[

vman-qos

|

vman-qos-dual-

number

|

vman-qos-dual-fp

number

]

ipv4pbr

number

}

ecfmacl

number

fcoeacl

number

iscsioptacl

number

Parameters

Command Modes

CONFIGURATION

Command

History

Usage

Information

You must save the new CAM settings to the startup-config (

write-mem

or

copy run start

) then reload

the system for the new settings to take effect.

The total amount of space allowed is 16 FP Blocks. System flow requires three blocks and these cannot
be reallocated. The

ipv4acl

profile range is 1-4.

When configuring space for IPv6 ACLs, the total number of Blocks must equal 13.

On the MXL 10/40GbE Switch IO Module, there can be

only one

odd number of Blocks in the CLI

configuration; the other Blocks must be in factors of two. For example, a CLI configuration of
5+4+2+1+1 Blocks is not supported; a configuration of 6+4+2+1 Blocks is supported.

Ranges for the CAM profiles are 1-10, except for the

ipv6acl

profile which is 0-10. The

ipv6acl

allocation must be a factor of two (2, 4, 6, 8, 10).

default

Use the default CAM profile settings, and set the CAM as follows.

•

L3 ACL (ipv4acl): 2

•

L2 ACL(l2acl): 2

•

IPv6 L3 ACL(ipv6Acl):0

•

L3 QoS (ipv4qos): 2

•

L2 QOS(L2Qos): 1

•

L2PT (L2PT): 0

•

MAC ACL (IpMacAcl): 0

•

VmanDualQos: 0

•

EcfmAcl: 0

•

FcoeAcl: 4

•

iscsiOptAcl: 2

l2acl

number

ipv4acl

number

ipv6acl

number

,

ipv4qos

number

l2qos

number

,

l2pt

number

ipmacacl

number

ecfmacl

number

[

vman-qos

|

vman--qos-dual

number

|

vman-qos-dual-fp

number

]

ipv4pbr

number

Allocate space to each CAM region.

Enter the CAM profile name followed by the amount of CAM
space to be allotted.

The total space allocated must equal 13.

The range for

ipv4acl

is 1 to 4.

The

ipv6acl

range must be a factor of 2.

The

vman-qos-dual-fp

number

must be entered as a multiple

of 4.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

«
...
146
147
148
149
150
...
»

Содержание Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Force10 MXL Blade

Express5800/T110g-S

Бренд: NEC Страницы: 34

Бренд: Vxl Страницы: 19

Бренд: Axis Страницы: 10

UltraNEXUS-HD X5

Бренд: Leightronix Страницы: 5

Бренд: X-media Страницы: 10

Бренд: Fujitsu Страницы: 280

Active Fabric Manager

Бренд: Dell Страницы: 44

Бренд: Dell Страницы: 120

Бренд: Dell Страницы: 76

Active Fabric Manager

Бренд: Dell Страницы: 127

Бренд: Dell Страницы: 122

DR4000 Restore Manager

Бренд: Dell Страницы: 156

Chassis Management Controller

Бренд: Dell Страницы: 234

Бренд: Dell Страницы: 160

Бренд: Dell Страницы: 160

Бренд: Dell Страницы: 190

Бренд: Dell Страницы: 133

Бренд: Dell Страницы: 165

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды