manualshive.com logo in svg

Dell Force10 MXL Blade, Справочное руководство, Страница: 319 / 732

Поделиться
Скачать
Dell Force10 MXL Blade Скачать руководство пользователя страница 319

IPv4 Routing |

319

Example

Figure 15-21.  show ip traffic Command Example (partial) 

Table 15-11.  show ip traffic output definitions

Keyword

Definition

unknown protocol...

No receiver for these packets. Counts those packets whose protocol type field is not 
recognized by FTOS.

not a gateway...

Packets can not be routed; host/network is unreachable.

security failures...

Counts the number of received unicast/multicast packets that could not be forwarded 
due to:

•

route not found for unicast/multicast; ingress interfaces do not belong to the 
destination multicast group

•

destination IP address belongs to reserved prefixes; host/network unreachable

bad options...

Unrecognized IP option on a received packet.

Frags:

IP fragments received.

... reassembled

Number of IP fragments that were reassembled.

... timeouts

Number of times a timer expired on a reassembled queue.

... too big

Number of invalid IP fragments received.

... couldn’t fragment

Number of packets that could not be fragmented and forwarded.

...encapsulation failed

Counts those packets which could not be forwarded due to ARP resolution failure. 
FTOS sends an arp request prior to forwarding an IP packet. If a reply is not 
received, FTOS repeats the request three times. These packets are counted in 
encapsulation failed.

Rcvd:

...short packets

The number of bytes in the packet are too small.

...bad length

The length of the packet was not correct.

...no port broadcasts

The incoming broadcast/multicast packet did not have any listener.

...socket full

The applications buffer was full and the incoming packet had to be dropped.

FTOS#show ip traffic  
IP statistics:
 Rcvd: 10021161 total, 3197480 local destination
    2501 format errors, 390 checksum errors, 0 bad hop count
    0 unknown protocol, 0 not a gateway
    115 security failures, 0 bad options
 Frags: 0 reassembled, 0 timeouts, 0 too big
     0 fragmented, 0 couldn't fragment
 Bcast: 6281 received, 0 sent; Mcast: 500 received, 0 sent
 Sent: 6573260 generated, 0 forwarded
    3830 encapsulation failed, 0 no route

ICMP statistics:
 Rcvd: 0 format errors, 0 checksum errors, 0 redirects, 3 unreachable
    0 echo, 0 echo reply, 0 mask requests, 0 mask replies, 0 quench
    0 parameter, 0 timestamp, 0 info request, 0 other
 Sent: 0 redirects, 1 unreachable, 0 echo, 0 echo reply
    0 mask requests, 0 mask replies, 0 quench, 0 timestamp
    0 info reply, 0 time exceeded, 0 parameter problem

UDP statistics:
 Rcvd: 2938110 total, 14 checksum errors, 1 no port
    0 short packets, 0 bad length, 1883908 no port broadcasts, 0 socket full
 Sent: 329731 total, 1883908 forwarded broadcasts
--More--

Содержание Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов