DataCard ImageCard Magna Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 180

background image

Troubleshooting

5-23

User’s Guide for Magna™ Platinum Series™ Printers

Obtaining service

For repair assistance, contact your service provider. Place the service call from a
telephone close to the printer so that you can access the printer and the PC running
the driver while talking to the service provider.

Before you call for service, make sure you have the information recorded during
troubleshooting, as described on

page 5-1

. Also, make sure you have the serial

number of the printer. It is located on a label that is visible when you open the top
cover of the printer.

When to obtain service

Perform the steps at the beginning of this chapter before obtaining service. Call for
service if:

•

A troubleshooting process instructs you to call service

•

A troubleshooting process does not produce the expected result

•

You experience a problem repeatedly

Packing the printer for shipping

When service requests that you return the printer to a service center for repair, pack
the printer for shipping. You might also need to pack the printer to send it to another
location.

Pack the printer

1

Turn off power to the printer. If the printer includes a laminator module, allow the
module to cool before packing.

2

Remove the power cord from the printer and power receptacle. Remove the data
cable and any other cables attached to the printer.

–

If you are shipping the printer to use at another location, pack the power cord,
data cable, and any other cables in the accessories box.

–

If you are shipping the printer for service, do not ship cables with the printer
unless asked to do so.

3

Remove all cards from the card cartridge, card output stacker, and printer.

4

Remove the card output stacker (step 1 in Figure 5-5) and the replaceable
cleaning sleeve (step 2 in Figure 5-5). Keep the cleaning spindle at your location
or follow the instructions from your service provider. Discard the used cleaning
sleeve.

«
...
93
94
95
96
97
...
»

Содержание ImageCard Magna





















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ImageCard Magna

IMAGEPRESS C7010VPS

Бренд: Canon Страницы: 4

iP2600 - PIXMA Color Inkjet Printer

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 8

ImageCLASS 2300

Бренд: Canon Страницы: 102

Бренд: Canon Страницы: 86

Бренд: Canon Страницы: 20

Бренд: Panasonic Страницы: 102

Бренд: ABLE Страницы: 26

Бренд: Eazao Страницы: 50

Бренд: Olivetti Страницы: 2

Бренд: Olivetti Страницы: 109

Бренд: Olivetti Страницы: 111

Бренд: Olivetti Страницы: 8

Бренд: Ultimaker Страницы: 30

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 16

PIXMA TR4500 Series

Бренд: Canon Страницы: 100

Бренд: Konica Minolta Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды