DataCard ImageCard Magna Скачать руководство пользователя страница 93

Страница: 93 / 180

Troubleshooting

5-21

Obtain guidance from service before performing this task.

User’s Guide for Magna™ Platinum Series™ Printers

Laminate patch is off the
trailing edge of the card.

There was slack in the
supply material.

The supply roll and
machine settings do not
match.

Supply material is upside
down after hand winding.

Machine settings were
changed during service.

The heated roller does not
move.

Apply laminate on another
card. If problem repeats, go
to the next solution.

Change supply rolls. If that
fixes the problem, request a
new supply roll. If it does
not, change the supply
advance. See the

-Guide.

Load the laminate supply
correctly. See

Chapter 2

Contact your service
representative.

Laminate patch is off the
leading edge of the card.

An overlay patch is on the
driver roller.

The rollers are dirty.

The supply tracker is
slipping.

The supply roll and
machine settings do not
match.

Machine settings were
changed during service.

Use a duplex/laminator
cleaning card. See

Chapter 4

Use a duplex/laminator
cleaning card. See

Chapter 4

Clean the supply tracker.
See

Chapter 4

Be sure your hands and the
materials used are clean
and free of grease or oil.

Change supply rolls. If that
does not fix the problem,
adjust the supply advance.

See

Chapter 4

Contact your service
representative.

Laminate patch is wrinkled
on the card.

Supply roll is not pushed
firmly onto supply spindle
or take-up spool is not
pushed firmly onto take-up
spindle.

The supply spindle needs
adjustment.

Load the laminate supply
again. See

Chapter 2

Contact your service
representative.

Table 5-4: Overlay quality problems

What you see

Possible causes

Solutions

Jane Doe

Содержание ImageCard Magna





















































































































































































Результаты поиска

Содержание ImageCard Magna

Отзывы:

Похожие инструкции для ImageCard Magna

Бренды по названию

Популярные бренды

DataCard ImageCard Magna, Руководство пользователя

Результаты поиска

Содержание ImageCard Magna

Отзывы:

Похожие инструкции для ImageCard Magna

Бренды по названию

Популярные бренды