DataCard ImageCard Magna Скачать руководство пользователя страница 107

Страница: 107 / 180

Install the printer

7-3

User’s Guide for Magna™ Platinum™ Series Printers

Save all packing material, including the plastic bag, shipping carton, shipping
support wrap, and accessories box.

Open the accessories box and remove the contents. The accessories box
contains:

–

Power cable

–

Data cable

–

Optional smart card cable(s)

–

Cleaning kit with printer cleaning card and replaceable cleaning sleeve

–

Card output stacker

–

Continuous cleaning roller spindle

–

Cleaning pen

–

Optional spool caps if the printer has a topcoat or overlay module

–

Warranty, declaration of conformity, and installation feedback report

–

User’s Guide

–

Printer driver CD-ROM

–

Supplies kit if one was ordered with this printer

10 Open the printer cover and then place the card output stacker on the right end of

the printer (

Figure 7-2

). The card output stacker hooks into the printer.

Figure 7-2: Place the card output stacker on the printer

11 Make sure the card cartridge is securely seated in the printer. If needed, move it

gently to seat it.

12 Remove the packaging material and printhead packing tape.

Lift the top cover.

Slide the packaging material off the edge of the cover (step1 in Figure 7-3).

Содержание ImageCard Magna





















































































































































































Результаты поиска

Содержание ImageCard Magna

Отзывы:

Похожие инструкции для ImageCard Magna

Бренды по названию

Популярные бренды

DataCard ImageCard Magna, Руководство пользователя

Результаты поиска

Содержание ImageCard Magna

Отзывы:

Похожие инструкции для ImageCard Magna

Бренды по названию

Популярные бренды