DataCard ImageCard Magna Скачать руководство пользователя страница 86

Страница: 86 / 180

5-14

Troubleshooting

Obtain guidance from service before performing this task.

User’s Guide for Magna™ Platinum Series™ Printers

The card shows irregular
lighter or darker spots.

The printhead is not
aligned correctly.

Contact your service
representative.

The card shows wrinkles
in dark areas of printing.

The printhead intensity is
too high.

The printhead is not
aligned correctly.

Decrease the printhead
intensity setting. See the

e-Guide

Contact your service
representative.

Part or all of the printed
image is expanded.

The printhead is not
installed properly.

Remove and reinstall the
printhead cartridge. See

Chapter 4

If the problem persists,
contact your service
representative.

Part or all of the printed
image is compressed.

The card path may be
obstructed.

The rollers might be dirty.

The cards might not meet
specifications.

Check the card transport
track for jams. or pass-
through module (if
present) for jams. Clear
any card jams.

Run a printer cleaning
cycle, then clean the
rollers. See

Chapter 4

Obtain and use a different
supply of cards. See

Appendix B

If the problem persists,
contact your service
representative.

Table 5-1: Print quality problems

What you see

Possible causes

Solutions

Содержание ImageCard Magna





















































































































































































Результаты поиска

Содержание ImageCard Magna

Отзывы:

Похожие инструкции для ImageCard Magna

Бренды по названию

Популярные бренды

DataCard ImageCard Magna, Руководство пользователя

Результаты поиска

Содержание ImageCard Magna

Отзывы:

Похожие инструкции для ImageCard Magna

Бренды по названию

Популярные бренды