DataCard ImageCard Magna Скачать руководство пользователя страница 16

Страница: 16 / 180

1-10

Overview

User’s Guide for Magna™ Platinum Series™ Printers

Back of the printer

Figure 1-7

shows the back of the Magna printer:

Figure 1-7: The back of the Magna printer

If the printer includes an optional laminator module, that module extends farther than
the ports and receptacles area.

Find the following on the back of the printer:

Data Port

The printer includes two data ports. Select only one data port to use.

•

ECP parallel port

Use the ECP parallel port to connect the printer's data cable to the PC, if the
printer was ordered with a parallel cable.

•

USB data port

Use the USB data port to connect the printer's data cable to the PC, if the printer
was ordered with a USB cable.

Power switch

Use the Power switch to power on or power off the printer.

Power

receptacle

This is the receptacle for connecting the power cable.

Power switch

Power receptacle

ECP parallel port

USB port

Optional smart card serial port

Data port

Security lock receptacle

Optional smart card USB port

Содержание ImageCard Magna





















































































































































































Результаты поиска

Содержание ImageCard Magna

Отзывы:

Похожие инструкции для ImageCard Magna

Бренды по названию

Популярные бренды

DataCard ImageCard Magna, Руководство пользователя

Результаты поиска

Содержание ImageCard Magna

Отзывы:

Похожие инструкции для ImageCard Magna

Бренды по названию

Популярные бренды