DataCard ImageCard Magna Скачать руководство пользователя страница 85

Страница: 85 / 180

Troubleshooting

5-13

Obtain guidance from service before performing this task.

User’s Guide for Magna™ Platinum Series™ Printers

Part of the printed image
is discolored.

Cards might have
fingerprints or other dirt on
them.

The cards might be
contaminated or otherwise
not meet specifications.

The rollers might be dirty.

A signature panel is
located on the other side
of the card.

Handle cards without
touching the surface to be
printed. Wear gloves when
handling unprinted cards.

Obtain and use a different
supply of cards. See

Appendix B

Run a printer cleaning
card, change the cleaning
sleeve, then clean the
rollers. See

Chapter 4

Redesign the card to
avoid printing photos over
signature panel residue.

The printed card shows
small unprinted spots.

The card is scratched, the
card surface is uneven, or
the card edge has burrs.

The replaceable cleaning
sleeve might be dirty.

The printer rollers might
be dirty.

If the problem occurs
frequently, obtain and use
a different supply of cards.
See

Appendix B

Run a printer cleaning
card and then change the
cleaning sleeve. See

Chapter 4.

Run a printer cleaning
card, change the cleaning
sleeve, and then clean the
rollers. See

Chapter 4

The printed card shows
wavy lines along the
length of the card
(woodgrain).

The print ribbon is not
loaded correctly.

The printhead is not
aligned correctly.

Load the print ribbon
again. Make sure the
cartridge is firmly seated.
See

Chapter 2

Contact your service
representative.

Table 5-1: Print quality problems

What you see

Possible causes

Solutions

Содержание ImageCard Magna





















































































































































































Результаты поиска

Содержание ImageCard Magna

Отзывы:

Похожие инструкции для ImageCard Magna

Бренды по названию

Популярные бренды

DataCard ImageCard Magna, Руководство пользователя

Результаты поиска

Содержание ImageCard Magna

Отзывы:

Похожие инструкции для ImageCard Magna

Бренды по названию

Популярные бренды