DataCard ImageCard Magna Скачать руководство пользователя страница 169

Страница: 169 / 180

D-5

User’s Guide for Magna™ Platinum Series™ Printers

•

The driver does not check the data you send. (The printer checks the data.) This
is the same behavior as magnetic stripe fonts.

On Windows 98, 98 SE, and Me, data formatted with escape codes cannot be located
in rotated fields.

•

For information about the characters allowed for each track format, see the
following section.

•

For more information about requirements for using escapes, see the
documentation for the non-Datacard printer.

Printer

Manufacturer

Encoding

Format

Syntax

Example

Eltron® IAT

(ISO)

~<track#><data>

~1ENCODING WITH ESCAPES

~21234567890

~31234567890

Atlantek IAT

(ISO)

~<track#>=<data>

~1=ENCODING WITH ESCAPES

~2=1234567890

~3=1234567890

Fargo® IAT

(ISO)

~<track#>(Start

Sentinel><Data>

~1%ENCODING WITH ESCAPES?

~2;1234567890?

~3;1234567890?

Datacard
HiFX™

IAT (ISO)

~<track#>(Start Sentinel><Data>
<End Sentinel>

~1%ENCODING WITH ESCAPES?

~2;1234567890?

~3;1234567890?

Victor Data
Systems

IAT (ISO)

~<track#>(Start Sentinel><Data>
<End Sentinel>

~1%ENCODING WITH ESCAPES?

~2;1234567890?

~3;1234567890?

Only the default start sentinel, a semicolon (;), is permitted.

Содержание ImageCard Magna





















































































































































































Результаты поиска

Содержание ImageCard Magna

Отзывы:

Похожие инструкции для ImageCard Magna

Бренды по названию

Популярные бренды

DataCard ImageCard Magna, Руководство пользователя

Результаты поиска

Содержание ImageCard Magna

Отзывы:

Похожие инструкции для ImageCard Magna

Бренды по названию

Популярные бренды