manualshive.com logo in svg

Danfoss VLT 5000 Series, Инструкция по эксплуатации, Страница: 190 / 240

Поделиться
Скачать
Danfoss VLT 5000 Series Скачать руководство пользователя страница 190

Select

Torque control, speed feedback

, if an encoder

feedback signal is to be generated. This is relevant in
winder and extruder applications.

Torque control, speed feedback,

 is selected if it is to be

possible to change the speed direction, while at the
same time maintaining the torque reference.
Set the following parameters in order shown:

Torque control, speed feedback:
Parameter:

Setting:

Data value:

100

Configuration

Torque control, speed feedback

[5]

200

Output frequency, range/direction

201

Output frequency, low limit

202

Output frequency, high limit

203

Reference/feedback range

204

Minimum reference

Only if [0] in par. 203

205

Maximum reference

414

Minimum feedback

415

Maximum feedback

306

Encoder feedback, input B

[24]

307

Encoder feedback, input A

[25]

329

Encoder feedback, pulse/rev

421

Speed PID low-pass filter time

448

Gear ratio

447

Torque regulation, speed feed-
back

449

Friction loss

After

Torque control, speed feedback

, has been selec-

ted, the adjustable frequency drive should be calibra-
ted to ensure that the current torque equals the torque
of the adjustable frequency drive. For this to be ensur-
ed, a torque gauge must be fitted to the shaft so as to
enable accurate adjustment of parameter 447, 

 Torque

compensation

, and parameter 449, 

 Friction loss

. It is

recommended to run an AMA before torque calibra-
tion. Proceed as follows before beginning to use the
system:

1.

Fit a torque gauge to the shaft.

2.

Start the motor with a positive torque refer-
ence and a positive direction of rotation.
Read the torque gauge.

3.

Using the same torque reference, change the
direction of rotation from positive to negative.

Read the torque and adjust it to the same
level as for the positive torque reference and
direction of rotation. This can be done by
means of parameter 449, 

Friction loss.

4.

Using a warm motor and approx. 50% load,
set parameter 447, 

Torque compensation

, to

match the torque gauge. The adjustable fre-
quency drive is now ready for operation.

Select

Special motor characteristics

 if the adjustable

frequency drive is to be adapted to a synchronous mo-
tor, parallel motor operation or if slip- compensation is
not required.
Set the following parameters in order shown:

Special motor characteristics:
Parameter:

Setting:

Data value:

101

Torque characteristics

Special motor characteristics

[5] or [15]

432 + 431

F5 frequency/U5 voltage

430 + 429

F4 frequency/U4 voltage

428 + 427

F3 frequency/U3 voltage

426 + 425

F2 frequency/U2 voltage

424 + 423

F1 frequency/U1 voltage

422

U0 voltage

VLT

®

 5000 Series

MG.51.C5.22 - VLT

p

 is a registered Danfoss trademark. 

 187

List of functions

Содержание VLT 5000 Series

















































































































































































































































Отзывы:

Нет отзывов