Daikin MC70L3VM L-Series страница 26 Скачать руководство пользователя

Страница: 26 / 59

SiBE811120

Operation Manual

Photocatalytic Air Purifier L-Series

UNIT1

Opposing pole plates

Ionised wire

Knob

Knob
(white)

Be careful not to cut the
internal ionised wires.

Opposing
pole plates

Removing and attaching the opposing pole plates

CAUTION

Wear rubber gloves to remove and attach the opposing pole plates. Hands can be cut on the opposing pole plates and ionised wires.

Ionising frame

Front panel

Remove

Remove the front panel and UNIT1.

Page 17.

Remove the opposing pole plates from
the rear of UNIT1.

Pinching the sets of knobs
on the right and left at the
same time makes it easier
to remove the opposing
pole plate.

Ionising frame

(green)

Page 17.

Attach UNIT1 and the front panel.

Arrow

Wear rubber

gloves.

The opposing pole plates have no difference between the
upper and the lower, or between the right and the left.
Attach them so that the arrow is visible.

Attach the opposing pole plates.

Attach

1) Fit the opposing pole plate over the knobs (2 sets on the

right and left) on the ionising frame.

Ionising frame

Opposing
pole plates

2) Insert securely until it clicks.

3) Attach the other opposing pole plate.

• Pinching together the white and green knobs (2 sets on

the right and left), lift the opposing pole plate up and
remove it.

Wear rubber

gloves.

Содержание MC70L3VM L-Series




























































Результаты поиска

Содержание MC70L3VM L-Series

Отзывы:

Похожие инструкции для MC70L3VM L-Series

Бренды по названию

Популярные бренды

Daikin MC70L3VM L-Series, Руководство по обслуживанию

Результаты поиска

Содержание MC70L3VM L-Series

Отзывы:

Похожие инструкции для MC70L3VM L-Series

Бренды по названию

Популярные бренды